research papers\(\def\hfill{\hskip 5em}\def\hfil{\hskip 3em}\def\eqno#1{\hfil {#1}}\)

Journal logoJOURNAL OF
SYNCHROTRON
RADIATION
ISSN: 1600-5775

Synchrotron PEEM and ToF-SIMS study of oxidized heterogeneous pentlandite, pyrrhotite and chalcopyrite

CROSSMARK_Color_square_no_text.svg

aIan Wark Research Institute, University of South Australia, Australia
*Correspondence e-mail: david.beattie@unisa.edu.au

(Received 25 May 2010; accepted 6 July 2010; online 28 July 2010)

Synchrotron-based photoemission electron microscopy (PEEM; probing the surface region) and time-of-flight secondary ion mass spectrometry (ToF-SIMS; probing the uppermost surface layer) have been used to image naturally heterogeneous samples containing chalcopyrite (CuFeS2), pentlandite [(Ni,Fe)9S8] and monoclinic pyrrhotite (Fe7S8) both freshly polished and exposed to pH 9 KOH for 30 min. PEEM images constructed from the metal L3 absorption edges were acquired for the freshly prepared and solution-exposed mineral samples. These images were also used to produce near-edge X-ray absorption fine-structure spectra from regions of the images, allowing the chemistry of the surface of each mineral to be interrogated, and the effect of solution exposure on the mineral surface chemistry to be determined. The PEEM results indicate that the iron in the monoclinic pyrrhotite oxidized preferentially and extensively, while the iron in the chalcopyrite and pentlandite underwent only mild oxidation. The ToF-SIMS data gave a clearer picture of the changes happening in the uppermost surface layer, with oxidation products being observed on all three minerals, and significant polysulfide formation and copper activation being detected for pyrrhotite.

1. Introduction

Ores that are mined for the extraction of metals contain many different minerals, not all of which are valuable. One of the most common means to separate valuable minerals from worthless minerals is the process of flotation. Flotation exploits differences in surface hydrophobicity to selectively separate the valuable minerals in an ore from the worthless mineral phases. The process involves passing gas bubbles through a suspension of the ground ore. Hydrophobic particles attach to the rising bubbles and are brought to the surface where they are skimmed off and collected, while hydrophilic particles remain in suspension (Wills & Napier-Munn, 2005[Wills, B. A. & Napier-Munn, T. (2005). Wills' Mineral Processing Technology, 7th ed., pp. 267-352. Oxford: Butterworth-Heinemann.]). Ores containing valuable metal sulfide minerals are commonly processed in this manner.

The surface chemistry of sulfide minerals is crucial to their effective flotation and separation from the associated worthless minerals. Oxidation in particular is an important process affecting sulfide floatability and selectivity (oxidation products can either enhance or diminish hydrophobicity); consequently the oxidation of sulfide minerals under processing related conditions has received a great deal of research attention. Metal sulfide minerals oxidize by diffusion of metal ions from the near surface layers to the surface where they oxidize to form a metal hydroxide, also resulting in a metal-depleted, sulfur-rich layer (Grano et al., 1997[Grano, S. R., Sollaart, M., Skinner, W., Prestidge, C. A. & Ralston, J. (1997). Int. J. Miner. Process. 50, 1-26.]; Vaughan et al., 1997[Vaughan, D. J., Becker, U. & Wright, K. (1997). Int. J. Miner. Process. 51, 1-14.]; Yin et al., 1995[Yin, Q., Kelsall, G. H., Vaughan, D. J. & England, K. E. R. (1995). Geochim. Cosmochim. Acta, 59, 1091-1100.], 2000[Yin, Q., Vaughan, D. J., England, K. E. R., Kelsall, G. H. & Brandon, N. P. (2000). J. Electrochem. Soc. 147, 2945-2951.]; Fairthorne et al., 1997[Fairthorne, G., Fornasiero, D. & Ralston, J. (1997). Int. J. Miner. Process. 49, 31-48.]; Todd et al., 2003[Todd, E. C., Sherman, D. M. & Purton, J. A. (2003). Geochim. Cosmochim. Acta, 67, 2137-2146.]; Mielczarski et al., 1996[Mielczarski, J. A., Cases, J. M., Alnot, M. & Ehrhardt, J. J. (1996). Langmuir, 12, 2519-2530.]; Parker et al., 2005[Parker, G. K., Woods, R. & Hope, G. A. (2005). Proc. Electrochem. Soc. 2004-18, 104-115.]; Harmer et al., 2006[Harmer, S. L., Thomas, J. E., Fornasiero, D. & Gerson, A. R. (2006). Geochim. Cosmochim. Acta, 70, 4392-4402.]).

Conventional X-ray photoemission spectroscopy (XPS) has been used in the study of mineral oxidation for some time (Buckley, 1994[Buckley, A. N. (1994). Colloids Surf. A, 93, 159-172.]; Buckley & Woods, 1984[Buckley, A. N. & Woods, R. (1984). Aust. J. Chem. 37, 2403-2413.]; Brion, 1980[Brion, D. (1980). Applic. Surf. Sci 5, 133-152.]). The improved resolution and surface sensitivity that synchrotron radiation affords XPS has been exploited to gain an even better understanding of mineral surface chemistry and the processes that occur on their surfaces, especially the initial state of the surface after fracture (Harmer et al., 2004[Harmer, S. L., Pratt, A. R., Nesbitt, W. H. & Fleet, M. E. (2004). Am. Miner. 89, 1026-1032.], 2005[Harmer, S. L., Pratt, A. R., Nesbitt, H. W. & Fleet, M. E. (2005). Can. Miner. 43, 1619-1630.], 2009[Harmer, S. L., Skinner, W. M., Buckley, A. N. & Fan, L.-J. (2009). Surf. Sci. 603, 537-545.]; Buckley et al., 2007[Buckley, A. N., Skinner, W. M., Harmer, S. L., Pring, A., Lamb, R. N., Fan, L.-J. & Yang, Y.-W. (2007). Can. J. Chem. 85, 767-781.]; Pratt, 2004[Pratt, A. (2004). Surf. Interface Anal. 36, 654-657.]). Oxidation states, the oxidation process and its effects on flotation have all been studied by synchrotron-based XPS (Harmer et al., 2006[Harmer, S. L., Thomas, J. E., Fornasiero, D. & Gerson, A. R. (2006). Geochim. Cosmochim. Acta, 70, 4392-4402.]; Acres et al., 2010a[Acres, R. G., Harmer, S. L. & Beattie, D. A. (2010a). Int. J. Miner. Process. 94, 43-51.],b[Acres, R. G., Harmer, S. L. & Beattie, D. A. (2010b). Miner. Eng. In the press.]; Laajalehto et al., 1997[Laajalehto, K., Kartio, I. & Suoninen, E. (1997). Int. J. Miner. Process. 51, 163-170.]; Buckley et al., 2003[Buckley, A. N., Goh, S. W., Lamb, R. N. & Woods, R. (2003). Int. J. Miner. Process. 72, 163-174.]) and also near-edge X-ray absorption fine structure (NEXAFS) (Goh et al., 2006a[Goh, S., Buckley, A., Lamb, R., Fan, L.-J., Jang, L.-Y. & Yang, Y.-W. (2006a). Phys. Chem. Miner. 33, 445-456.],c[Goh, S. W., Buckley, A. N. & Lamb, R. N. (2006c). Miner. Eng. 19, 204-208.],d[Goh, S. W., Buckley, A. N., Lamb, R. N., Rosenberg, R. A. & Moran, D. (2006d). Geochim. Cosmochim. Acta, 70, 2210-2228.]; Mikhlin & Tomashevich, 2005[Mikhlin, Y. & Tomashevich, Y. (2005). Phys. Chem. Miner. 32, 19-27.]; Buckley et al., 2007[Buckley, A. N., Skinner, W. M., Harmer, S. L., Pring, A., Lamb, R. N., Fan, L.-J. & Yang, Y.-W. (2007). Can. J. Chem. 85, 767-781.]).

Photoemission electron microscopy (PEEM) is a synchrotron technique that has not yet been applied to the study of sulfide mineral oxidation, in spite of it offering significant benefits over bulk NEXAFS for composite/heterogeneous materials. The advantages of PEEM for such studies are that it provides surface chemical imaging as well as chemical state and bonding information. Imaging is critical as a surface's hydrophobicity depends not only on the proportion of the hydrophobic and hydrophilic surface species but also on their distribution. While time-of-flight secondary ion mass spectrometry (ToF-SIMS) is able to produce maps of elemental distribution across a mineral surface, it does not provide the same degree of chemical information as XPS or NEXAFS. Imaging conventional XPS does provide chemical imaging, but with a spatial resolution too poor to highlight the different domains in most heterogeneous mineral samples. Only two synchrotron imaging techniques have the surface sensitivity and spatial resolution for flotation-related surface studies of heterogeneous minerals with grains/domains in the micrometre to sub-micrometre range: scanning photoelectron spectroscopy (SPEM) and PEEM. The data produced by PEEM (elemental images as well as NEXAFS spectra from each pixel in the image) have the potential to provide significant insights into the development of sulfide mineral surface chemistry of heterogeneous mineral samples. Another advantage of PEEM is the ability to easily extract data from any given point on the surface, allowing one to investigate how a surface changes with distance from a feature or grain interface. PEEM has been applied to heterogeneous minerals by Smith et al. (1998[Smith, A. D., Cressey, G., Schofield, P. F. & Cressey, B. A. (1998). J. Synchrotron Rad. 5, 1108-1110.]) and Schmidt et al. (2001[Schmidt, O., Fazan, T. A., Morais, J. & Fecher, G. H. (2001). Surf. Sci. 482-485, 568-573.]) to image the distribution of mineral phases across natural samples. However, these studies were concerned with identification of mineral phases within heterogeneous samples, rather than the study of surface processes.

In this study, PEEM is applied to polished surfaces of samples containing three metal sulfides: chalcopyrite, pentlandite and pyrrhotite. Chalcopyrite (CuFeS2) and pentlandite [(Fe,Ni)9S8] are the most significant sources of industrial copper and nickel, respectively (Legrand et al., 1997[Legrand, D. L., Bancroft, G. M. & Nesbitt, H. W. (1997). Int. J. Miner. Process. 51, 217-228.], 2005[Legrand, D. L., Bancroft, G. M. & Nesbitt, H. W. (2005). Am. Miner. 90, 1042-1054.]; Buckley & Woods, 1984[Buckley, A. N. & Woods, R. (1984). Aust. J. Chem. 37, 2403-2413.], 1991[Buckley, A. N. & Woods, R. (1991). Surf. Interface Anal. 17, 675-680.]; Harmer et al., 2004[Harmer, S. L., Pratt, A. R., Nesbitt, W. H. & Fleet, M. E. (2004). Am. Miner. 89, 1026-1032.]) and are often associated with the iron sulfide pyrrhotite (Fe1–xS) (Bozkurt et al., 1998[Bozkurt, V., Xu, Z. & Finch, J. A. (1998). Int. J. Miner. Process. 52, 203-214.]; Newell et al., 2006[Newell, A. J. H., Bradshaw, D. J. & Harris, P. J. (2006). Miner. Eng. 19, 675-686.]; Kelebek et al., 1996[Kelebek, S., Wells, P. F. & Fekete, S. O. (1996). Can. Metall. Q. 35, 329-336.]; Kelebek, 1993[Kelebek, S. (1993). XVIII International Mineral Processing Congress. Sydney: Australasian Institute of Mining and Metallurgy.]; Miller et al., 2005[Miller, J. D., Li, J., Davidtz, J. C. & Vos, F. (2005). Miner. Eng. 18, 855-865.]; Kolahdoozan, 2002[Kolahdoozan, M. (2002). Int. J. Eng. Sci. 13, 135-144.]; Agar, 1991[Agar, G. E. (1991). Int. J. Miner. Process. 33, 1-19.]; Yoon et al., 1995[Yoon, R. H., Basilio, C. I., Marticorena, M. A., Kerr, A. N. & Stratton-Crawley, R. (1995). Miner. Eng. 8, 807-816.]). Pyrrhotite is usually considered a worthless minerals phase and separated magnetically or by flotation in order to maximize the grade of nickel ore concentrate and minimize sulfur dioxide emissions during smelting (Bozkurt et al., 1998[Bozkurt, V., Xu, Z. & Finch, J. A. (1998). Int. J. Miner. Process. 52, 203-214.]; Kelebek et al., 1996[Kelebek, S., Wells, P. F. & Fekete, S. O. (1996). Can. Metall. Q. 35, 329-336.]; Khan & Kelebek, 2004[Khan, A. & Kelebek, S. (2004). J. Appl. Electrochem. 34, 849-856.]; Kelebek, 1993[Kelebek, S. (1993). XVIII International Mineral Processing Congress. Sydney: Australasian Institute of Mining and Metallurgy.]; Kolahdoozan, 2002[Kolahdoozan, M. (2002). Int. J. Eng. Sci. 13, 135-144.]; Bozkurt et al., 1999[Bozkurt, V., Xu, Z. & Finch, J. A. (1999). Can. Metall. Q. 38, 105-112.]; Agar, 1991[Agar, G. E. (1991). Int. J. Miner. Process. 33, 1-19.]; Heiskanen et al., 1991[Heiskanen, K., Kirjavainen, V. & Laapas, H. (1991). Int. J. Miner. Process. 33, 263-274.]; Senior et al., 1995[Senior, G. D., Trahar, W. J. & Guy, P. J. (1995). Int. J. Miner. Process. 43, 209-234.]), but is recovered when processing platinum group mineral ores (Miller et al., 2005[Miller, J. D., Li, J., Davidtz, J. C. & Vos, F. (2005). Miner. Eng. 18, 855-865.]; Buswell et al., 2002[Buswell, A. M., Bradshaw, D. J., Harris, P. J. & Ekmekci, Z. (2002). Miner. Eng. 15, 395-404.]). In this work the samples have been studied as freshly polished surfaces and polished surfaces oxidized in solution at pH 9, in order to study the development of oxidation products on each mineral phase across the surface, particularly near interfaces between minerals.

The PEEM studies reported in this work are combined with measurements of the same surfaces using ToF-SIMS. ToF-SIMS is a popular tool for studying the changes to mineral surfaces arising from processing-related conditions (Harmer et al., 2008[Harmer, S. L., Mierczynska-Vasilev, A., Beattie, D. A. & Shapter, J. G. (2008). Miner. Eng. 21, 1005-1012.]; Khmeleva et al., 2005[Khmeleva, T. N., Georgiev, T. V., Jasieniak, M., Skinner, W. M. & Beattie, D. A. (2005). Surf. Interface Anal. 37, 699-709.]; Piantadosi et al., 2000[Piantadosi, C., Jasieniak, M., Skinner, W. M. & Smart, R. S. C. (2000). Miner. Eng. 13, 1377-1394.]; Smart et al., 1998[Smart, R. S. C., Amarantidis, J., Skinner, W., Prestidge, C. A., La Vanier, L. & Grano, S. (1998). Scanning Microsc. 12, 553-583.], 2000[Smart, R. S. C., Jasieniak, M., Prince, K. E. & Skinner, W. M. (2000). Miner. Eng. 13, 857-870.]; Priest et al., 2008[Priest, C., Stevens, N., Sedev, R., Skinner, W. & Ralston, J. (2008). J. Colloid Interface Sci. 320, 563-568.]; Pratt et al., 1998[Pratt, A. R., Franzreb, K. & McIntyre, N. S. (1998). Surf. Interface Anal. 26, 869-871.]) and is an ideal complimentary technique to PEEM analysis, given the monolayer sensitivity of the former and the surface-to-bulk sensitivity of the latter. In fact, SIMS has been used previously to study the oxidation of a composite sulfide mineral surface (Pratt et al., 1998[Pratt, A. R., Franzreb, K. & McIntyre, N. S. (1998). Surf. Interface Anal. 26, 869-871.]), with the study focusing on the degree of hydration of the mineral oxidation products. Our work combines the high surface selectivity of ToF-SIMS with the slightly deeper surface probe of PEEM to give a more complete picture of the development of surface oxidation products on a heterogeneous metal sulfide mineral surface.

2. Experimental

2.1. Minerals and materials

Samples used in this study were cut from a core sample from Frood Mine in the Sudbury Basin, Ontario, Canada. Samples containing all three phases (chalcopyrite, pyrrhotite and pentlandite) were selected and polished. The purity and stoichiometry of the phases in these heterogeneous samples was determined using a CAMECA SX51 electron microprobe operating at 20 kV and 20 nA. Measurements were taken from ten points on each region and averaged: chalcopyrite CuFeS2.05; pentlandite Fe4.49Ni3.99Co0.18S8.00; pyrrhotite Fe7.00S7.77. The stoichiometry of the pyrrhotite in the sample indicates that it is monoclinic and not hexagonal; no significant stoichiometric variation was detected across the area of pyrrhotite analysed. The sample also displayed magnetism, which is characteristic of monoclinic pyrrhotite.

Ultrapure water was produced on a Millipore MilliQ Element system with a resistivity of 18.0 MΩ cm−1. A pH 9 KOH solution was produced by dissolving reagent-grade (>90%) KOH in ultrapure water. The diamond polishing compounds were Struers DP-Stick Ps with particle sizes of 1 µm and 0.25 µm. The silica polishing suspension used was Struers OP-U suspension (particle size 0.04 µm) adjusted to pH 7 using dilute HCl.

2.2. Surface preparation and modification

Samples were cut from the massive sample using a slow diamond saw and then shaped and abraded using 600 then 1200 grit silicon carbide paper, lubricated with ultrapure water. A small amount of 1 µm diamond paste was applied to a Beuhler Trident polishing pad and the sample worked by hand in a figure-8 pattern approximately 4 cm in length, then worked on a clean section of the polishing pad again in a figure-8 pattern. Polishing with 0.25 µm diamond paste followed the same procedure as with the 1 µm paste. Final polishing was carried out with 0.04 µm silica suspension in the same manner as diamond polishing, but on a Struers NAP polishing pad, pre-wetted with ultrapure water. One sample was analysed as fresh polished and the other was oxidized by immersion in pH 9 KOH for 30 min. Polishing of the un-oxidized sample was timed to be complete just before the oxidized sample was removed from solution, to enable both to be placed in the PEEM vacuum chamber at the same time. After immersion the oxidized sample was rinsed in clean pH 9 KOH solution to stop solution species from drying onto the surface. Excess rinse solution was removed using lint-free laboratory wipes without touching the surface to be analysed. Backscattered scanning electron (BSE) micrographs of the regions studied by PEEM on the fresh polished and oxidized samples are given in Fig. 1[link]. BSE phase contrast between chalcopyrite and pentlandite was not possible owing to the limitations of the backscatter detector on this instrument.

[Figure 1]
Figure 1
Backscattered electron micrograph of the regions investigated by PEEM on polished composite minerals containing chalcopyrite, pyrrhotite and pentlandite (Fr = sample analysed by freshly polished PEEM; Ox = sample analysed by PEEM after oxidation).

2.3. Scanning electron microscopy analysis

Scanning electron microscopy and energy dispersive analysis of X-rays (EDAX) were performed on a CamScan 44FE fitted with a field emission electron gun and EDAX detector. A primary electron beam accelerating voltage of 20 kV was used with the spot size set to 10. Micrographs were imaged using the backscatter detector to provide mineral phase contrast. EDAX X-ray maps were collected for copper, iron and nickel by rastering the beam across the surface. In order to confirm phase identity, EDAX spectra were collected from the exact regions imaged with PEEM. EDAX spectra were standardless and collected in spot mode until the peak channel counts were ∼10000 with a dead-time ratio of ∼45%. EDAX spectra were collected only as an indication of the phases present on the regions probed by PEEM. More accurate determinations of the stoichiometry were determined by electron microprobe analysis before PEEM was conducted.

2.4. PEEM analysis

PEEM experiments were conducted on beamline BL05B2 at the National Synchrotron Radiation Research Centre (NSRRC), Taiwan. BL05B2 uses an elliptically polarized undulator (EPU5) with a spherical-grating monochromator, providing 2 × 1012 photons s−1 at 800 eV and a beam of 0.4 mm × 0.2 mm. Images are generated by collecting the total electron yield (TEY) signal on a phosphor screen mounted on a CCD detector.

Varying the excitation energy across the range of a desired peak generates a stacked PEEM image where each layer represents a discrete excitation energy and the intensity of each pixel represents the TEY signal intensity at that energy for the area of the sample projected onto the pixel. NEXAFS spectra can be derived from specific points on the image from the pixel intensities on each layer. 40 × 40 pixel regions were analysed to obtain an acceptable signal-to-noise ratio. Copper, nickel and iron spectra were calibrated using metallic standards and published values for the L3 peak energy [Cu metal 932.6 eV (Goh et al., 2006d[Goh, S. W., Buckley, A. N., Lamb, R. N., Rosenberg, R. A. & Moran, D. (2006d). Geochim. Cosmochim. Acta, 70, 2210-2228.]), Fe metal 707.7 eV (Pearce et al., 2006[Pearce, C. I., Pattrick, R. A. D., Vaughan, D. J., Henderson, C. M. B. & van der Laan, G. (2006). Geochim. Cosmochim. Acta, 70, 4635-4642.]), Ni metal 852.7 eV (Blanchard et al., 2008[Blanchard, P. E. R., Grosvenor, A. P., Cavell, R. G. & Mar, A. (2008). Chem. Mater. 20, 7081-7088.]; Goh et al., 2006b[Goh, S., Buckley, A., Lamb, R., Skinner, W., Pring, A., Wang, H., Fan, L.-J., Jang, L.-Y., Lai, L.-J. & Yang, Y.-W. (2006b). Phys. Chem. Miner. 33, 98-105.])]. TEY probe depths are up to approximately 12 monolayers, with approximately 40% of the signal originating from the first four monolayers. The NEXAFS spectra energy resolution is as follows: Cu, 0.17 eV (15 µm slit); Ni, 0.14 eV (15 µm slit); Fe, 0.11 eV (15 µm slot). Spectra were normalized such that the height of the peak corresponding to the bulk metal was 1 and the baseline of the pre-edge background was 0.

2.5. ToF-SIMS analysis

ToF-SIMS analysis in this study was conducted on a PHI TRIFT II static SIMS instrument. A Ga+ liquid-metal ion gun was the primary ion source, operating at a current of 600 pA and 25 kV excitation voltage. Images were collected using a raster size of either 200 × 200 µm or 100 × 100 µm. Images were divided into regions of interest approximately 20 × 20 µm to 30 × 30 µm in size. Negative ion and positive ion spectra were collected from each individual region of interest (ROI) and normalized to the maximum intensity and averaged over the total number of ROIs for that sample. At least 32 ROIs were defined per sample, from images taken at several points on the sample. ROI boundaries were set within the contrast edges of the regions. The analysis of multiple ROIs allowed for the determination of signal variability and associated confidence intervals (95% probability) for the signal of each surface component (Piantadosi et al., 2000[Piantadosi, C., Jasieniak, M., Skinner, W. M. & Smart, R. S. C. (2000). Miner. Eng. 13, 1377-1394.]; Piantadosi & Smart, 2002[Piantadosi, C. & Smart, R. S. C. (2002). Int. J. Miner. Process. 64, 43-54.]). ToF-SIMS peak intensities vary significantly depending on the surface environment [the matrix effect (Vickerman, 2001[Vickerman, J. C. (2001). ToF-SIMS: Surface Analysis by Mass Spectrometry, edited by J. C. Vickerman and D. Briggs, pp. 1-40. Chichester/Manchester: IM Publications.])]. As a result of this dependence, ToF-SIMS is not able to quantify the surface composition since no sensitivity factors exist (as in XPS) and relative peak intensities must be compared qualitatively.

3. Results

3.1. Freshly polished sample

Iron, copper and nickel PEEM images from a region on the fresh polished sample containing all three mineral phases are presented in Fig. 2[link] alongside corresponding EDAX X-ray maps. The PEEM images (on the left of Fig. 2[link]) indicate two major regions with either a dominant copper signal or a dominant iron signal, and four smaller regions with a high signal from nickel. Given the stoichiometry of the three minerals investigated here, the high copper region can be identified as chalcopyrite, the high iron region as pyrrhotite, and the three high nickel regions as pentlandite. This initial identification is confirmed with the EDAX X-ray maps (Fig. 2[link], right). The stoichiometry of the regions analysed (from the acquired EDAX spectra) is as follows: pentlandite Ni4Fe4S8; pyrrhotite Fe7S8; chalcopyrite CuFeS2.

[Figure 2]
Figure 2
Iron, copper and nickel PEEM images (left) and EDAX X-ray maps (right) of the freshly polished sample. Each mineral phase is labelled: Po, pyrrhotite; Cp, chalcopyrite; Pn, pentlandite (regions highlighted within ovals).

The PEEM images in Fig. 2[link] were used to extract TEY NEXAFS spectra of the metals of interest for the three mineral phases. Fig. 3[link] shows the Cu L3 TEY NEXAFS spectrum from the chalcopyrite phase (Fig. 3[link], inset position A) and Ni L3 TEY NEXAFS spectrum from the pentlandite phase (Fig. 3[link], inset position B) in the freshly polished sample. Fig. 3[link] also shows Fe L2,3 TEY NEXAFS spectra from points on each region: chalcopyrite (position A), pentlandite (position B) and pyrrhotite (position C). Image inserts indicate the points where each spectrum originated from the individual PEEM images. The Cu L3 spectrum of the chalcopyrite in the polished sample shows a single peak at 932.6 eV corresponding to Cu(I) in chalcopyrite (Buckley et al., 2007[Buckley, A. N., Skinner, W. M., Harmer, S. L., Pring, A., Lamb, R. N., Fan, L.-J. & Yang, Y.-W. (2007). Can. J. Chem. 85, 767-781.]; Goh et al., 2006c[Goh, S. W., Buckley, A. N. & Lamb, R. N. (2006c). Miner. Eng. 19, 204-208.],d[Goh, S. W., Buckley, A. N., Lamb, R. N., Rosenberg, R. A. & Moran, D. (2006d). Geochim. Cosmochim. Acta, 70, 2210-2228.]; Mikhlin et al., 2004[Mikhlin, Y. L., Tomashevich, Y. V., Asanov, I. P., Okotrub, A. V., Varnek, V. A. & Vyalikh, D. V. (2004). Appl. Surf. Sci. 225, 395-409.]; Pearce et al., 2006[Pearce, C. I., Pattrick, R. A. D., Vaughan, D. J., Henderson, C. M. B. & van der Laan, G. (2006). Geochim. Cosmochim. Acta, 70, 4635-4642.]) and there is no evidence of a Cu(II) shoulder on the low binding energy side of the peak around 931 eV. There is a broad post-edge feature in the Cu L3 spectrum at approximately 936–940 eV. This post-edge feature is enhanced owing to interference from the I0 signal recorded on the Au grid, which was contaminated with copper. The interference does not affect the shape or position of the Cu L3 peak. The fresh polished Ni L3 spectrum has a single peak at 853.2 eV corresponding to Ni(II) as in pentlandite [853.2 eV (Goh et al., 2006b[Goh, S., Buckley, A., Lamb, R., Skinner, W., Pring, A., Wang, H., Fan, L.-J., Jang, L.-Y., Lai, L.-J. & Yang, Y.-W. (2006b). Phys. Chem. Miner. 33, 98-105.])] with no clear indication of other peaks or shoulders.

[Figure 3]
Figure 3
TEY NEXAFS spectra (polished sample) of Cu L3 (top left) from chalcopyrite (inset point A), Ni L3 (bottom left) from pentlandite (inset point B) and Fe L2,3 (right) from chalcopyrite (point A), pentlandite (point B) and pyrrhotite (point C).

The Fe L2,3 spectra from all three regions are plotted on the right of Fig. 3[link], with the three spectra showing the characteristic Fe L3 and L2 peaks at 706.8 eV and 719.5 eV, respectively (Mikhlin et al., 2004[Mikhlin, Y. L., Tomashevich, Y. V., Asanov, I. P., Okotrub, A. V., Varnek, V. A. & Vyalikh, D. V. (2004). Appl. Surf. Sci. 225, 395-409.], 2005[Mikhlin, Y., Tomashevich, Y., Tauson, V., Vyalikh, D., Molodtsov, S. & Szargan, R. (2005). J. Electron Spect. Rel. Phenom. 142, 83-88.]; Goh et al., 2006d[Goh, S. W., Buckley, A. N., Lamb, R. N., Rosenberg, R. A. & Moran, D. (2006d). Geochim. Cosmochim. Acta, 70, 2210-2228.]; Pearce et al., 2006[Pearce, C. I., Pattrick, R. A. D., Vaughan, D. J., Henderson, C. M. B. & van der Laan, G. (2006). Geochim. Cosmochim. Acta, 70, 4635-4642.]). Upon closer inspection the Fe L3 peak of each mineral phase has some additional structure. The chalcopyrite and pentlandite phases on the freshly polished sample (Fig. 3[link], positions A and B, respectively) show one dominant Fe L3 peak from the bulk minerals, but there is also a small almost fully resolved pre-edge feature at 705.5 eV. This pre-edge feature can be attributed to transitions of the Fe L3 electrons to multiple unoccupied electron eigenstates [multiplets (Ikeno et al., 2009[Ikeno, H., De Groot, F. M. F., Stavitski, E. & Tanaka, I. (2009). J. Phys. Condens. Matter, 21, 104208.])] just below the ionization threshold. It should be noted that the similarity in the Fe L2,3 spectrum of pentlandite to that of chalcopyrite is not due to a contribution from chalcopyrite underlying the small pentlandite grains analysed. The TEY sampling depth (12 monolayers) is smaller than the EDAX detection depth; no Cu was detected in EDAX spectra from the pentlandite regions of the sample, or in the pentlandite regions of the EDAX X-ray map shown in Fig. 2[link].

For the freshly polished pyrrhotite (Fig. 3[link], position C) there is some evidence of a pre-edge feature in addition to the peak at 706.8 eV, but the main additional structure in the Fe L3 spectrum is a strong shoulder on the high binding energy side of the main peak at approximately 708 eV giving a line shape resembling that published by Mikhlin & Tomashevich (2005[Mikhlin, Y. & Tomashevich, Y. (2005). Phys. Chem. Miner. 32, 19-27.]) and Goh et al. (2006d[Goh, S. W., Buckley, A. N., Lamb, R. N., Rosenberg, R. A. & Moran, D. (2006d). Geochim. Cosmochim. Acta, 70, 2210-2228.]) for abraded pyrrhotite. The shoulder position corresponds to iron oxidation products (iron oxide and hydroxide) [708–709 eV (Mikhlin et al., 2004[Mikhlin, Y. L., Tomashevich, Y. V., Asanov, I. P., Okotrub, A. V., Varnek, V. A. & Vyalikh, D. V. (2004). Appl. Surf. Sci. 225, 395-409.], 2005[Mikhlin, Y., Tomashevich, Y., Tauson, V., Vyalikh, D., Molodtsov, S. & Szargan, R. (2005). J. Electron Spect. Rel. Phenom. 142, 83-88.]; Goh et al., 2006d[Goh, S. W., Buckley, A. N., Lamb, R. N., Rosenberg, R. A. & Moran, D. (2006d). Geochim. Cosmochim. Acta, 70, 2210-2228.]; Mikhlin & Tomashevich, 2005[Mikhlin, Y. & Tomashevich, Y. (2005). Phys. Chem. Miner. 32, 19-27.])].

3.2. Oxidized sample

PEEM images collected from the polished sample exposed to pH 9 KOH for 30 min are presented in Fig. 4[link] with matching EDAX X-ray maps. Three large phases are distinguishable with higher concentrations of iron, copper and nickel comprising approximately a third of the image each. EDAX spectra confirmed the high iron, nickel and copper phases to be pyrrhotite (Fe7S8), pentlandite (Ni4Fe4S8) and chalcopyrite (CuFeS2), respectively.

[Figure 4]
Figure 4
Iron, copper and nickel PEEM images (left) and EDAX X-ray maps (right) from the sample exposed to pH 9 KOH for 30 min. Each mineral phase is labelled: Po, pyrrhotite; Cp, chalcopyrite; Pn, pentlandite.

After oxidation the Cu L3 NEXAFS spectrum from the chalcopyrite phase (Fig. 5[link], position A) shows no variance from the Cu L3 from the freshly polished sample, with a single peak at 932.6 eV from Cu(I) in chalcopyrite and no evidence of a Cu(II) shoulder. Like the Cu L3 NEXAFS spectrum from the chalcopyrite phases, the Ni L3 NEXAFS spectrum from oxidized pentlandite (Fig. 5[link], position B) phases show little variation from the fresh sample, with a single peak at 853.2 eV. The Fe L2,3 NEXAFS spectra from the three different oxidized mineral phases (A, chalcopyrite; B, pentlandite; C, pyrrhotite) are also given in Fig. 5[link]. The spectra from chalcopyrite and pentlandite are very similar to those obtained from the fresh polished sample, with a dominant L3 peak at 706.8 eV. However, upon closer inspection, it appears that the L3 peak is slightly broader for pentlandite, indicating the presence of a small amount of iron oxidation products. In addition, the pre-edge feature on the L3 peak for pentlandite is not as well resolved as in the case of the freshly polished pentlandite. In contrast to pentlandite and chalcopyrite, where there are either minor or no indications of oxidation, the Fe L2,3 spectrum of pyrrhotite has indications of significant further oxidation following exposure of the mineral sample of alkaline solution. The presence of the resolved 708.2 eV Fe L3 peak is a clear indication that substantial oxidation has occurred on the pyrrhotite surface and the near-surface region. In addition, the L2 Fe peak in this spectrum can also be seen to contain two components, one for bulk Fe in pyrrhotite and one for the oxidation products on the pyrrhotite surface. Pyrrhotite has oxidized extensively, especially when compared with pentlandite. The increased oxidation of pyrrhotite relative to the other minerals, indicated by the increased intensity of the peak at 708.2 eV, is as expected due to the high reactivity of pyrrhotite (Kolahdoozan, 2002[Kolahdoozan, M. (2002). Int. J. Eng. Sci. 13, 135-144.]; Miller et al., 2005[Miller, J. D., Li, J., Davidtz, J. C. & Vos, F. (2005). Miner. Eng. 18, 855-865.]; Agar, 1991[Agar, G. E. (1991). Int. J. Miner. Process. 33, 1-19.]; Goh et al., 2006d[Goh, S. W., Buckley, A. N., Lamb, R. N., Rosenberg, R. A. & Moran, D. (2006d). Geochim. Cosmochim. Acta, 70, 2210-2228.]; Pratt et al., 1994[Pratt, A. R., Muir, I. J. & Nesbitt, H. W. (1994). Geochim. Cosmochim. Acta, 58, 827-841.]; Mycroft et al., 1995[Mycroft, J. R., Nesbitt, H. W. & Pratt, A. R. (1995). Geochim. Cosmochim. Acta, 59, 721-733.]; Buckley et al., 1988[Buckley, A. N., Hamilton, I. C. & Woods, R. (1988). Proceedings of the International Symposium on Electrochemistry in Mineral and Metal Processing II, edited by P. E. Richardson and R. Woods, pp. 234-246. Pennington: The Electrochemical Society.]; Buckley & Woods, 1985[Buckley, A. N. & Woods, R. (1985). Applic. Surf. Sci. 22-23, 280-287.]).

[Figure 5]
Figure 5
TEY NEXAFS spectra (oxidized sample) of Cu L3 (top left) from chalcopyrite (inset point A), Ni L3 (bottom left) from pentlandite (inset point B) and Fe L2,3 (right) from chalcopyrite (point A), pentlandite (point B) and pyrrhotite (point C).

The presence of small amounts of iron oxidation products on pentlandite is confirmed by performing a subtraction of the fresh mineral spectrum from that of the oxidized mineral; the subtraction spectra for all three mineral phases are given in Fig. 6[link]. The residual from the subtraction is almost flat for chalcopyrite (Fig. 6a[link]). However, the subtraction spectrum for pentlandite (Fig. 6b[link]) has a small residual peak at approximately 708 eV, the position identified previously as Fe from iron hydroxide/oxide oxidation products. This observation indicates that pentlandite has undergone minor oxidation during the 30 min exposure to pH 9 solution. It would be expected that any spectral indication of oxidation of chalcopyrite and pentlandite would appear in the Fe L3,2 spectrum as iron will oxidize preferentially over copper in chalcopyrite, and over nickel in pentlandite (Yin et al., 1995[Yin, Q., Kelsall, G. H., Vaughan, D. J. & England, K. E. R. (1995). Geochim. Cosmochim. Acta, 59, 1091-1100.]; Buckley et al., 1985[Buckley, A. N., Hamilton, I. C. & Woods, R. (1985). Developments in Mineral Processing Flotation of Sulfide Minerals, edited by K. S. E. Forssberg, pp. 41-60. Amsterdam/New York: Elsevier.]; Buckley & Woods, 1984[Buckley, A. N. & Woods, R. (1984). Aust. J. Chem. 37, 2403-2413.], 1991[Buckley, A. N. & Woods, R. (1991). Surf. Interface Anal. 17, 675-680.]; Velasquez et al., 2005[Velasquez, P., Leinen, D., Pascual, J., Ramos-Barrado, J. R., Grez, P., Gomez, H., Schrebler, R., Del Rio, R. & Cordova, R. (2005). J. Phys. Chem. B, 109, 4977-4988.]; Legrand et al., 1997[Legrand, D. L., Bancroft, G. M. & Nesbitt, H. W. (1997). Int. J. Miner. Process. 51, 217-228.]; Richardson & Vaughan, 1989[Richardson, S. & Vaughan, D. J. (1989). Mineral. Mag. 53, 213-222.]). The indications for the presence of oxidation products on the pyrrhotite surface do not require spectral subtraction for elucidation. However, the subtraction has been performed for the two pyrrhotite surfaces (fresh and oxidized) and this spectrum is given in Fig. 6(c)[link] along with those for the two other minerals.

[Figure 6]
Figure 6
Subtraction TEY NEXAFS Fe L2,3 spectra from (a) chalcopyrite (oxidized point A − fresh point A), (b) pentlandite (oxidized point B − fresh point B) and (c) pyrrhotite (oxidized point C − fresh point C).

The oxidation of the pyrrhotite phase has been further investigated by extracting the Fe L2,3 NEXAFS spectrum of pyrrhotite from near the phase boundary (position D) and comparing this with the spectrum extracted from the image point far from the phase boundary (position C). These spectra are compared in Fig. 7[link], along with a subtraction spectrum of the near phase boundary spectrum from the far-from phase boundary spectrum. This type of NEXAFS spectral comparison is only possible with PEEM. The spectrum from near the phase boundary has a larger contribution from the L3 peak of Fe in pyrrhotite (706 eV); the degree of oxidation of pyrrhotite is reduced the closer to the phase boundary one probes.

[Figure 7]
Figure 7
Comparison of TEY NEXAFS Fe L2,3 spectra from oxidized pyrrhotite, far from the phase boundary (C), near the phase boundary (D) and the subtraction spectrum (C − D).

3.3. ToF-SIMS comparison

The TEY NEXAFS spectra collected in this study are sensitive to the mineral composition and coordination of metal atoms in the surface and near-surface region (e.g. the maximum depth probed was up to 12 monolayers). To get a picture of what is occurring on the very top surface layer (one to three monolayers), one has to use a probe of surface composition with higher surface selectivity. ToF-SIMS is one such probe: it provides compositional maps and can be used to compare surfaces before and after surface treatments. However, the higher degree of surface selectivity comes at a price: there is no spectral information, only mass information.

ToF-SIMS images from a freshly polished composite sample of chalcopyrite, pyrrhotite and pentlandite are presented in Fig. 8[link], with individual images constructed from the Cu, Fe and Ni mass peaks being combined to give a fourth overlay image that indicates the three different mineral phases (red, pyrrhotite; blue, pentlandite; green, chalcopyrite). The sample region is different from that analysed using PEEM but still contains the same three mineral phases in intimate contact. The signal from iron is present across the surface, which is to be expected given that iron is a major component of all three minerals. Also expected is the occurrence of nickel only in regions that can be identified as pentlandite; pyrrhotite and chalcopyrite contain no nickel. However, the signal from copper is seen across all three mineral phases, despite the fact that the bulk composition of the pyrrhotite and pentlandite indicates no copper. This is also in contrast to the PEEM images displayed in Fig. 2[link]. The explanation for the disagreement most likely lies in the depth of sampling of ToF-SIMS and PEEM; ToF-SIMS will see primarily the first monolayer of material on the polished surface whereas PEEM sees up to 12 monolayers into the surface layer. Copper is observed on the surfaces of the pentlandite and pyrrhotite phases after polishing. It is likely that the layer of copper observed in the ToF-SIMS spectra is very thin and has arisen as a result of copper activation [uptake of dissolved copper into mineral surfaces (Finkelstein, 1997[Finkelstein, N. P. (1997). Int. J. Miner. Process. 52, 81-120.])] from copper liberated into the polishing slurry from the chalcopyrite region of the sample.

[Figure 8]
Figure 8
Cu, Ni and Fe and composite ToF-SIMS images from a polished composite sample containing chalcopyrite, pyrrhotite and pentlandite.

The ToF-SIMS ion images in Fig. 8[link] clearly allow one to designate regions of different mineralogy in the sample. Of more use for this investigation are the normalized peak intensities from positive and negative ions collected during the ToF-SIMS analysis. These mass peak intensities are plotted in Figs. 9[link], 10[link] and 11[link] (top, positive ions; bottom, negative ions) for chalcopyrite, pentlandite and pyrrhotite, respectively. The major mass peaks of interest are Fe, Cu, Si, Ni (positive ions), and S, Sn (n = 2–5), C and O (negative ions). The data in each figure include the normalized mass peak intensities before and after the freshly polished surface has been exposed to the pH 9 solution, i.e. before and after solution oxidation.

[Figure 9]
Figure 9
Normalized peak intensities from positive (top) and negative (bottom) ion ToF-SIMS of freshly polished and oxidized chalcopyrite. The inset in the negative-ion graph is an expansion of the sulfur species peak intensities. Light grey, freshly polished; dark grey, oxidized in pH 9 solution. Error bars represent the statistically significant confidence intervals (P = 95%) for each mass signal.
[Figure 10]
Figure 10
Normalized peak intensities from positive (top) and negative (bottom) ion ToF-SIMS of freshly polished and oxidized pentlandite. The inset in the negative-ion graph is an expansion of the sulfur species peak intensities. Light grey, freshly polished; dark grey, oxidized in pH 9 solution. Error bars represent the statistically significant confidence intervals (P = 95%) for each mass signal.
[Figure 11]
Figure 11
Normalized peak intensities from positive (top) and negative (bottom) ion ToF-SIMS of freshly polished and oxidized pyrrhotite. The inset in the negative-ion graph is an expansion of the sulfur species peak intensities. Light grey, freshly polished; dark grey, oxidized in pH 9 solution. Error bars represent the statistically significant confidence intervals (P = 95%) for each mass signal.

The ToF-SIMS data for chalcopyrite (Fig. 9[link]) indicate that the solution oxidation has resulted in a statistically significant increase in iron and oxygen, and a statistically significant decrease in the amount of copper and sulfur. The insert in the negative-ion spectrum in Fig. 9[link] shows different length sulfur chains normalized to the total sulfur. There was also an increase in the amount of S2 produced at the chalcopyrite surface after oxidation as can be seen from the insert. These observations are consistent with mild oxidation of the chalcopyrite surface, with the production of iron hydroxide products, release of copper into solution, and the formation of surface sulfur species, such as disulfide and polysulfide (Acres et al., 2010a[Acres, R. G., Harmer, S. L. & Beattie, D. A. (2010a). Int. J. Miner. Process. 94, 43-51.]; Buckley & Woods, 1984[Buckley, A. N. & Woods, R. (1984). Aust. J. Chem. 37, 2403-2413.]). An almost identical picture is generated for the development of the pentlandite surface when the data in Fig. 10[link] are inspected. The data in the figure indicate that iron and oxygen increase, while nickel and sulfur decrease (along with an increase in S2, seen clearly in the insert in Fig. 10[link]), again consistent with mild oxidation of the pentlandite surface. The data for pentlandite and chalcopyrite indicate that oxidation is occurring for these two mineral phases during exposure to pH 9 solution. Mild oxidation of chalcopyrite or pentlandite in air or alkaline solution produces a surface rich in polysulfides and some iron hydroxides (Buckley & Woods, 1984[Buckley, A. N. & Woods, R. (1984). Aust. J. Chem. 37, 2403-2413.]; Legrand et al., 1997[Legrand, D. L., Bancroft, G. M. & Nesbitt, H. W. (1997). Int. J. Miner. Process. 51, 217-228.], 2005[Legrand, D. L., Bancroft, G. M. & Nesbitt, H. W. (2005). Am. Miner. 90, 1042-1054.]; Buckley & Woods, 1991[Buckley, A. N. & Woods, R. (1991). Surf. Interface Anal. 17, 675-680.]; Richardson & Vaughan, 1989[Richardson, S. & Vaughan, D. J. (1989). Mineral. Mag. 53, 213-222.]; Buckley et al., 1985[Buckley, A. N., Hamilton, I. C. & Woods, R. (1985). Developments in Mineral Processing Flotation of Sulfide Minerals, edited by K. S. E. Forssberg, pp. 41-60. Amsterdam/New York: Elsevier.]; Mielczarski et al., 1996[Mielczarski, J. A., Cases, J. M., Alnot, M. & Ehrhardt, J. J. (1996). Langmuir, 12, 2519-2530.]; Todd et al., 2003[Todd, E. C., Sherman, D. M. & Purton, J. A. (2003). Geochim. Cosmochim. Acta, 67, 2137-2146.]). Surface polysulfides are the species responsible for hydrophobicity in the absence of collectors (Hayes et al., 1987[Hayes, R. A., Price, D. M., Ralston, J. & Smith, R. W. (1987). Miner. Process. Extr. Metall. Rev. 2, 203-234.]; Zachwieja et al., 1989[Zachwieja, J. B., McCarron, J. J., Walker, G. W. & Buckley, A. N. (1989). J. Colloid Interface Sci. 132, 462-468.]; Fairthorne et al., 1997[Fairthorne, G., Fornasiero, D. & Ralston, J. (1997). Int. J. Miner. Process. 49, 31-48.]; Senior & Trahar, 1991[Senior, G. D. & Trahar, W. J. (1991). Int. J. Miner. Process. 33, 321-341.]). The oxidation of both minerals observed here is restricted to the first few monolayers of the surface. However, it is likely that the oxidation does penetrate further into the surface region, as indications of minor oxidation were also seen in the Fe NEXAFS spectrum of pentlandite presented in Fig. 5[link].

The ToF-SIMS data for pyrrhotite are given in Fig. 11[link]. As with the previous two mineral phases, there are a number of differences in the normalized intensity of some positive and negative ions. However, there are a number of key differences. First, the amount of iron and oxygen on the pyrrhotite surface has actually decreased, albeit only slightly, and for the mineral that had the largest initial signals for these atoms at the surface. This is accompanied by an increase in copper and an increase in sulfur (pyrrhotite is the only phase to indicate an increase in sulfur at the surface following oxidation). Another point of note from the data in Fig. 11[link] is the increase in all sulfur polymer fragments (S2, S3, S4 and S5; see Fig. 11[link] insert). The data indicate that the surface of pyrrhotite has extensive amounts of sulfur oxidation products, increased copper activation and a small decrease in iron oxidation products. The last piece of information needs to be taken in the context of the depth of analysis of the ToF-SIMS experiments (top few monolayers). The PEEM data in Fig. 5[link] indicated clearly that there was a significant increase in the amount of iron hydroxide in the top 12 monolayers of the surface following oxidation. The oxidation of pyrrhotite has resulted in a significant degree of iron oxidation that penetrates into the near-surface region, and has left an outermost surface layer (the top one to three monolayers) rich in polysulfides, with evidence of extensive copper activation.

4. Discussion

Surface changes during oxidation are crucial to flotation and are different for mixtures of minerals compared with single minerals owing to processes such as inter-mineral galvanic interactions or the adsorption of metal ions rendering the surface `active' for collectors (Yelloji Rao & Natarajan, 1989[Yelloji Rao, M. K. & Natarajan, K. A. (1989). Int. J. Miner. Process. 27, 279-293.]; Ekmekçi & Demirel, 1997[Ekmekçi, Z. & Demirel, H. (1997). Int. J. Miner. Process. 52, 31-48.]; Holmes & Crundwell, 1995[Holmes, P. R. & Crundwell, F. K. (1995). Hydrometallurgy, 39, 353-375.]; Nakazawa & Iwasaki, 1986[Nakazawa, H. & Iwasaki, I. (1986). Int. J. Miner. Process. 18, 203-215.]; Kelebek & Nanthakumar, 2007[Kelebek, S. & Nanthakumar, B. (2007). Int. J. Miner. Process. 84, 69-80.]; Cheng et al., 1999[Cheng, X., Iwasaki, I. & Smith, K. A. (1999). Miner. Metall. Process. 16, 69-71.]; Pozzo & Iwasaki, 1988[Pozzo, R. L. & Iwasaki, I. (1988). Proceedings of the International Symposium on Electrochemistry in Mineral and Metal Processing II, edited by P. E. Richardson and R. Woods, pp. 66-83. Pennington: The Electrochemical Society.]; Yoon et al., 1995[Yoon, R. H., Basilio, C. I., Marticorena, M. A., Kerr, A. N. & Stratton-Crawley, R. (1995). Miner. Eng. 8, 807-816.]; Harmer et al., 2008[Harmer, S. L., Mierczynska-Vasilev, A., Beattie, D. A. & Shapter, J. G. (2008). Miner. Eng. 21, 1005-1012.]). Galvanic interactions between minerals occur due to differences in mineral rest potentials. Due to their semiconducting nature, when two sulfides are in electrical contact in solution a galvanic pair can be created where the mineral with the higher rest potential will act as a cathode and the mineral with the lower rest potential forming the anode. For the minerals studied in this investigation the order of rest potentials is chalcopyrite > pentlandite > pyrrhotite (Cheng et al., 1999[Cheng, X., Iwasaki, I. & Smith, K. A. (1999). Miner. Metall. Process. 16, 69-71.]; Bozkurt et al., 1998[Bozkurt, V., Xu, Z. & Finch, J. A. (1998). Int. J. Miner. Process. 52, 203-214.]; Buswell et al., 2002[Buswell, A. M., Bradshaw, D. J., Harris, P. J. & Ekmekci, Z. (2002). Miner. Eng. 15, 395-404.]; Khan & Kelebek, 2004[Khan, A. & Kelebek, S. (2004). J. Appl. Electrochem. 34, 849-856.]; Ralston, 1991[Ralston, J. (1991). Miner. Eng. 4, 859-878.]).

Preferential oxidation of pyrrhotite with minimal alteration of chalcopyrite and minor oxidation of pentlandite is in agreement with the literature on galvanic interactions, where the cathode is protected while the oxidation at the anode is accelerated (Ekmekçi & Demirel, 1997[Ekmekçi, Z. & Demirel, H. (1997). Int. J. Miner. Process. 52, 31-48.]; Yelloji Rao & Natarajan, 1989[Yelloji Rao, M. K. & Natarajan, K. A. (1989). Int. J. Miner. Process. 27, 279-293.]). Given the relative rest potentials of the three minerals, pyrrhotite will act as an anode in the three mineral coupling, with chalcopyrite as the cathode (Cheng et al., 1999[Cheng, X., Iwasaki, I. & Smith, K. A. (1999). Miner. Metall. Process. 16, 69-71.]; Bozkurt et al., 1998[Bozkurt, V., Xu, Z. & Finch, J. A. (1998). Int. J. Miner. Process. 52, 203-214.]; Buswell et al., 2002[Buswell, A. M., Bradshaw, D. J., Harris, P. J. & Ekmekci, Z. (2002). Miner. Eng. 15, 395-404.]; Khan & Kelebek, 2004[Khan, A. & Kelebek, S. (2004). J. Appl. Electrochem. 34, 849-856.]; Ralston, 1991[Ralston, J. (1991). Miner. Eng. 4, 859-878.]; Miller et al., 2005[Miller, J. D., Li, J., Davidtz, J. C. & Vos, F. (2005). Miner. Eng. 18, 855-865.]). Minerals with intermediate rest potentials in a multi-mineral coupling may act either as a cathode or anode depending on its rest potential (Cheng et al., 1999[Cheng, X., Iwasaki, I. & Smith, K. A. (1999). Miner. Metall. Process. 16, 69-71.]; Pozzo & Iwasaki, 1988[Pozzo, R. L. & Iwasaki, I. (1988). Proceedings of the International Symposium on Electrochemistry in Mineral and Metal Processing II, edited by P. E. Richardson and R. Woods, pp. 66-83. Pennington: The Electrochemical Society.]). In this case the lack of major oxidation of pentlandite indicates that it is most likely acting cathodically.

Although galvanic interaction can explain the majority of observations from the PEEM and ToF-SIMS data, it cannot explain the greater oxidation of pyrrhotite away from an interface relative to near the interface. For regions of pyrrhotite with the same composition, the galvanic interaction `off interface' should be the same as `near interface'. EDAX measurements showed no variance in the composition of the pyrrhotite along the mineral toward the phase boundary. One plausible explanation for the observed difference is that the solution composition above the near and far regions of the pyrrhotite was slightly different during the oxidation. The sample was in a non-stirred solution, with the possible result that a chemical gradient in solution was established during the oxidation (e.g. the persistence of localized dissolution species in the interfacial areas). This possibility will be explored in future studies with immersion/oxidation being performed in a flowing/stirred solution.

Finally, the observation of copper activation on the freshly polished surface indicates that care must be taken if highly surface-sensitive measurements are to be made on a surface prepared by polishing. Since PEEM has a more significant probe depth compared with ToF-SIMS, the presence of copper at the surface (one to three monolayers) would not have as dramatic an influence on the acquired spectra. This would actually appear to be an advantage of PEEM of polished surfaces when compared with ToF-SIMS.

5. Conclusions

PEEM has been successfully employed to image a heterogeneous mineral (before and after solution oxidation) containing pyrrhotite, pentlandite and chalcopyrite and identify regions where these mineral phases are in intimate contact. From these PEEM images, each mineral phase has been individually probed using TEY NEXAFS. The NEXAFS results show the pyrrhotite phase has oxidized preferentially to the chalcopyrite and pentlandite and that oxidation occurs at a greater rate away from an interface. ToF-SIMS results show that some oxidation of the pentlandite and chalcopyrite phases has occurred, but, since there is only minor indications of oxidation products in the NEXAFS spectra for pentlandite and almost no indication of oxidation for chalcopyrite, this oxidation is only superficial in terms of the depth probed by TEY, and when compared with the oxidation observed in pyrrhotite. Copper has been observed on all phases of the freshly polished sample with ToF-SIMS, indicating that liberated copper present in the polishing slurry has adsorbed and reacted with the other phases (copper activation). Nevertheless, polishing is a suitable preparation method for PEEM analysis owing to the increased depth probed for PEEM as compared with ToF-SIMS.

Acknowledgements

The authors would like to acknowledge financial support from the Australian Research Council Linkage Scheme (AMSRI, LP0667828), AMIRA International, and the sponsors of AMIRA International Project P924: BHP/Billiton, Rio Tinto, Orica Explosives, Anglo Platinum, Xstrata Technology, Freeport McMoran and AREVA NC. The authors would also like to thank Associate Professor Bill Skinner (Ian Wark Research Institute, University of South Australia) for supplying the mineral samples. Synchrotron PEEM analysis was conducted at the National Synchrotron Radiation Research Centre (NSRRC), Taiwan, and the authors would like to thank the BL05B2 team for their assistance.

References

First citationAcres, R. G., Harmer, S. L. & Beattie, D. A. (2010a). Int. J. Miner. Process. 94, 43–51.  Web of Science CrossRef CAS Google Scholar
First citationAcres, R. G., Harmer, S. L. & Beattie, D. A. (2010b). Miner. Eng. In the press.  Google Scholar
First citationAgar, G. E. (1991). Int. J. Miner. Process. 33, 1–19.  CrossRef CAS Web of Science Google Scholar
First citationBlanchard, P. E. R., Grosvenor, A. P., Cavell, R. G. & Mar, A. (2008). Chem. Mater. 20, 7081–7088.  Web of Science CrossRef CAS Google Scholar
First citationBozkurt, V., Xu, Z. & Finch, J. A. (1998). Int. J. Miner. Process. 52, 203–214.  Web of Science CrossRef CAS Google Scholar
First citationBozkurt, V., Xu, Z. & Finch, J. A. (1999). Can. Metall. Q. 38, 105–112.  CrossRef CAS Google Scholar
First citationBrion, D. (1980). Applic. Surf. Sci 5, 133–152.  CrossRef CAS Web of Science Google Scholar
First citationBuckley, A. N. (1994). Colloids Surf. A, 93, 159–172.  CrossRef CAS Web of Science Google Scholar
First citationBuckley, A. N., Goh, S. W., Lamb, R. N. & Woods, R. (2003). Int. J. Miner. Process. 72, 163–174.  Web of Science CrossRef CAS Google Scholar
First citationBuckley, A. N., Hamilton, I. C. & Woods, R. (1985). Developments in Mineral Processing Flotation of Sulfide Minerals, edited by K. S. E. Forssberg, pp. 41–60. Amsterdam/New York: Elsevier.  Google Scholar
First citationBuckley, A. N., Hamilton, I. C. & Woods, R. (1988). Proceedings of the International Symposium on Electrochemistry in Mineral and Metal Processing II, edited by P. E. Richardson and R. Woods, pp. 234–246. Pennington: The Electrochemical Society.  Google Scholar
First citationBuckley, A. N., Skinner, W. M., Harmer, S. L., Pring, A., Lamb, R. N., Fan, L.-J. & Yang, Y.-W. (2007). Can. J. Chem. 85, 767–781.  Web of Science CrossRef CAS Google Scholar
First citationBuckley, A. N. & Woods, R. (1984). Aust. J. Chem. 37, 2403–2413.  CrossRef CAS Google Scholar
First citationBuckley, A. N. & Woods, R. (1985). Applic. Surf. Sci. 2223, 280–287.  CrossRef CAS Google Scholar
First citationBuckley, A. N. & Woods, R. (1991). Surf. Interface Anal. 17, 675–680.  CrossRef CAS Web of Science Google Scholar
First citationBuswell, A. M., Bradshaw, D. J., Harris, P. J. & Ekmekci, Z. (2002). Miner. Eng. 15, 395–404.  Web of Science CrossRef CAS Google Scholar
First citationCheng, X., Iwasaki, I. & Smith, K. A. (1999). Miner. Metall. Process. 16, 69–71.  CAS Google Scholar
First citationEkmekçi, Z. & Demirel, H. (1997). Int. J. Miner. Process. 52, 31–48.  Google Scholar
First citationFairthorne, G., Fornasiero, D. & Ralston, J. (1997). Int. J. Miner. Process. 49, 31–48.  CrossRef CAS Web of Science Google Scholar
First citationFinkelstein, N. P. (1997). Int. J. Miner. Process. 52, 81–120.  Web of Science CrossRef CAS Google Scholar
First citationGoh, S., Buckley, A., Lamb, R., Fan, L.-J., Jang, L.-Y. & Yang, Y.-W. (2006a). Phys. Chem. Miner. 33, 445–456.  Web of Science CrossRef CAS Google Scholar
First citationGoh, S., Buckley, A., Lamb, R., Skinner, W., Pring, A., Wang, H., Fan, L.-J., Jang, L.-Y., Lai, L.-J. & Yang, Y.-W. (2006b). Phys. Chem. Miner. 33, 98–105.  Web of Science CrossRef CAS Google Scholar
First citationGoh, S. W., Buckley, A. N. & Lamb, R. N. (2006c). Miner. Eng. 19, 204–208.  Web of Science CrossRef CAS Google Scholar
First citationGoh, S. W., Buckley, A. N., Lamb, R. N., Rosenberg, R. A. & Moran, D. (2006d). Geochim. Cosmochim. Acta, 70, 2210–2228.  Web of Science CrossRef CAS Google Scholar
First citationGrano, S. R., Sollaart, M., Skinner, W., Prestidge, C. A. & Ralston, J. (1997). Int. J. Miner. Process. 50, 1–26.  CrossRef CAS Web of Science Google Scholar
First citationHarmer, S. L., Mierczynska-Vasilev, A., Beattie, D. A. & Shapter, J. G. (2008). Miner. Eng. 21, 1005–1012.  Web of Science CrossRef CAS Google Scholar
First citationHarmer, S. L., Pratt, A. R., Nesbitt, H. W. & Fleet, M. E. (2005). Can. Miner. 43, 1619–1630.  Web of Science CrossRef CAS Google Scholar
First citationHarmer, S. L., Pratt, A. R., Nesbitt, W. H. & Fleet, M. E. (2004). Am. Miner. 89, 1026–1032.  CAS Google Scholar
First citationHarmer, S. L., Skinner, W. M., Buckley, A. N. & Fan, L.-J. (2009). Surf. Sci. 603, 537–545.  Web of Science CrossRef CAS Google Scholar
First citationHarmer, S. L., Thomas, J. E., Fornasiero, D. & Gerson, A. R. (2006). Geochim. Cosmochim. Acta, 70, 4392–4402.  Web of Science CrossRef CAS Google Scholar
First citationHayes, R. A., Price, D. M., Ralston, J. & Smith, R. W. (1987). Miner. Process. Extr. Metall. Rev. 2, 203–234.  CrossRef CAS Google Scholar
First citationHeiskanen, K., Kirjavainen, V. & Laapas, H. (1991). Int. J. Miner. Process. 33, 263–274.  CrossRef CAS Web of Science Google Scholar
First citationHolmes, P. R. & Crundwell, F. K. (1995). Hydrometallurgy, 39, 353–375.  CrossRef CAS Web of Science Google Scholar
First citationIkeno, H., De Groot, F. M. F., Stavitski, E. & Tanaka, I. (2009). J. Phys. Condens. Matter, 21, 104208.  Web of Science CrossRef PubMed Google Scholar
First citationKelebek, S. (1993). XVIII International Mineral Processing Congress. Sydney: Australasian Institute of Mining and Metallurgy.  Google Scholar
First citationKelebek, S. & Nanthakumar, B. (2007). Int. J. Miner. Process. 84, 69–80.  Web of Science CrossRef CAS Google Scholar
First citationKelebek, S., Wells, P. F. & Fekete, S. O. (1996). Can. Metall. Q. 35, 329–336.  CrossRef CAS Web of Science Google Scholar
First citationKhan, A. & Kelebek, S. (2004). J. Appl. Electrochem. 34, 849–856.  Web of Science CrossRef CAS Google Scholar
First citationKhmeleva, T. N., Georgiev, T. V., Jasieniak, M., Skinner, W. M. & Beattie, D. A. (2005). Surf. Interface Anal. 37, 699–709.  Web of Science CrossRef CAS Google Scholar
First citationKolahdoozan, M. (2002). Int. J. Eng. Sci. 13, 135–144.  CAS Google Scholar
First citationLaajalehto, K., Kartio, I. & Suoninen, E. (1997). Int. J. Miner. Process. 51, 163–170.  CrossRef CAS Web of Science Google Scholar
First citationLegrand, D. L., Bancroft, G. M. & Nesbitt, H. W. (1997). Int. J. Miner. Process. 51, 217–228.  CrossRef CAS Web of Science Google Scholar
First citationLegrand, D. L., Bancroft, G. M. & Nesbitt, H. W. (2005). Am. Miner. 90, 1042–1054.  Web of Science CrossRef CAS Google Scholar
First citationMielczarski, J. A., Cases, J. M., Alnot, M. & Ehrhardt, J. J. (1996). Langmuir, 12, 2519–2530.  CrossRef CAS Web of Science Google Scholar
First citationMikhlin, Y. L., Tomashevich, Y. V., Asanov, I. P., Okotrub, A. V., Varnek, V. A. & Vyalikh, D. V. (2004). Appl. Surf. Sci. 225, 395–409.  Web of Science CrossRef CAS Google Scholar
First citationMikhlin, Y. & Tomashevich, Y. (2005). Phys. Chem. Miner. 32, 19–27.  Web of Science CrossRef CAS Google Scholar
First citationMikhlin, Y., Tomashevich, Y., Tauson, V., Vyalikh, D., Molodtsov, S. & Szargan, R. (2005). J. Electron Spect. Rel. Phenom. 142, 83–88.  Web of Science CrossRef CAS Google Scholar
First citationMiller, J. D., Li, J., Davidtz, J. C. & Vos, F. (2005). Miner. Eng. 18, 855–865.  Web of Science CrossRef CAS Google Scholar
First citationMycroft, J. R., Nesbitt, H. W. & Pratt, A. R. (1995). Geochim. Cosmochim. Acta, 59, 721–733.  CrossRef CAS Web of Science Google Scholar
First citationNakazawa, H. & Iwasaki, I. (1986). Int. J. Miner. Process. 18, 203–215.  CrossRef CAS Web of Science Google Scholar
First citationNewell, A. J. H., Bradshaw, D. J. & Harris, P. J. (2006). Miner. Eng. 19, 675–686.  Web of Science CrossRef CAS Google Scholar
First citationParker, G. K., Woods, R. & Hope, G. A. (2005). Proc. Electrochem. Soc. 2004–18, 104–115.  CAS Google Scholar
First citationPearce, C. I., Pattrick, R. A. D., Vaughan, D. J., Henderson, C. M. B. & van der Laan, G. (2006). Geochim. Cosmochim. Acta, 70, 4635–4642.  Web of Science CrossRef CAS Google Scholar
First citationPiantadosi, C., Jasieniak, M., Skinner, W. M. & Smart, R. S. C. (2000). Miner. Eng. 13, 1377–1394.  Web of Science CrossRef Google Scholar
First citationPiantadosi, C. & Smart, R. S. C. (2002). Int. J. Miner. Process. 64, 43–54.  Web of Science CrossRef CAS Google Scholar
First citationPozzo, R. L. & Iwasaki, I. (1988). Proceedings of the International Symposium on Electrochemistry in Mineral and Metal Processing II, edited by P. E. Richardson and R. Woods, pp. 66–83. Pennington: The Electrochemical Society.  Google Scholar
First citationPratt, A. (2004). Surf. Interface Anal. 36, 654–657.  Web of Science CrossRef CAS Google Scholar
First citationPratt, A. R., Franzreb, K. & McIntyre, N. S. (1998). Surf. Interface Anal. 26, 869–871.  CrossRef CAS Google Scholar
First citationPratt, A. R., Muir, I. J. & Nesbitt, H. W. (1994). Geochim. Cosmochim. Acta, 58, 827–841.  CrossRef CAS Web of Science Google Scholar
First citationPriest, C., Stevens, N., Sedev, R., Skinner, W. & Ralston, J. (2008). J. Colloid Interface Sci. 320, 563–568.  Web of Science CrossRef PubMed CAS Google Scholar
First citationRalston, J. (1991). Miner. Eng. 4, 859–878.  CrossRef Web of Science Google Scholar
First citationRichardson, S. & Vaughan, D. J. (1989). Mineral. Mag. 53, 213–222.  CrossRef CAS Web of Science Google Scholar
First citationSchmidt, O., Fazan, T. A., Morais, J. & Fecher, G. H. (2001). Surf. Sci. 482485, 568–573.  Web of Science CrossRef CAS Google Scholar
First citationSenior, G. D. & Trahar, W. J. (1991). Int. J. Miner. Process. 33, 321–341.  CrossRef CAS Web of Science Google Scholar
First citationSenior, G. D., Trahar, W. J. & Guy, P. J. (1995). Int. J. Miner. Process. 43, 209–234.  CrossRef CAS Web of Science Google Scholar
First citationSmart, R. S. C., Amarantidis, J., Skinner, W., Prestidge, C. A., La Vanier, L. & Grano, S. (1998). Scanning Microsc. 12, 553–583.  Google Scholar
First citationSmart, R. S. C., Jasieniak, M., Prince, K. E. & Skinner, W. M. (2000). Miner. Eng. 13, 857–870.  Web of Science CrossRef CAS Google Scholar
First citationSmith, A. D., Cressey, G., Schofield, P. F. & Cressey, B. A. (1998). J. Synchrotron Rad. 5, 1108–1110.  Web of Science CrossRef CAS IUCr Journals Google Scholar
First citationTodd, E. C., Sherman, D. M. & Purton, J. A. (2003). Geochim. Cosmochim. Acta, 67, 2137–2146.  Web of Science CrossRef CAS Google Scholar
First citationVaughan, D. J., Becker, U. & Wright, K. (1997). Int. J. Miner. Process. 51, 1–14.  CrossRef CAS Web of Science Google Scholar
First citationVelasquez, P., Leinen, D., Pascual, J., Ramos-Barrado, J. R., Grez, P., Gomez, H., Schrebler, R., Del Rio, R. & Cordova, R. (2005). J. Phys. Chem. B, 109, 4977–4988.  Web of Science CrossRef PubMed CAS Google Scholar
First citationVickerman, J. C. (2001). ToF-SIMS: Surface Analysis by Mass Spectrometry, edited by J. C. Vickerman and D. Briggs, pp. 1–40. Chichester/Manchester: IM Publications.  Google Scholar
First citationWills, B. A. & Napier-Munn, T. (2005). Wills' Mineral Processing Technology, 7th ed., pp. 267–352. Oxford: Butterworth-Heinemann.  Google Scholar
First citationYelloji Rao, M. K. & Natarajan, K. A. (1989). Int. J. Miner. Process. 27, 279–293.  CrossRef Google Scholar
First citationYin, Q., Kelsall, G. H., Vaughan, D. J. & England, K. E. R. (1995). Geochim. Cosmochim. Acta, 59, 1091–1100.  CrossRef CAS Web of Science Google Scholar
First citationYin, Q., Vaughan, D. J., England, K. E. R., Kelsall, G. H. & Brandon, N. P. (2000). J. Electrochem. Soc. 147, 2945–2951.  Web of Science CrossRef CAS Google Scholar
First citationYoon, R. H., Basilio, C. I., Marticorena, M. A., Kerr, A. N. & Stratton-Crawley, R. (1995). Miner. Eng. 8, 807–816.  CrossRef CAS Web of Science Google Scholar
First citationZachwieja, J. B., McCarron, J. J., Walker, G. W. & Buckley, A. N. (1989). J. Colloid Interface Sci. 132, 462–468.  CrossRef CAS Web of Science Google Scholar

© International Union of Crystallography. Prior permission is not required to reproduce short quotations, tables and figures from this article, provided the original authors and source are cited. For more information, click here.

Journal logoJOURNAL OF
SYNCHROTRON
RADIATION
ISSN: 1600-5775
Follow J. Synchrotron Rad.
Sign up for e-alerts
Follow J. Synchrotron Rad. on Twitter
Follow us on facebook
Sign up for RSS feeds