feature articles
Pressure effects on
and bio-membrane assembliesaDepartment of Chemistry, Imperial College London, South Kensington Campus, London SW7 2AZ, England
*Correspondence e-mail: nicholas.brooks@imperial.ac.uk
Membranes are amongst the most important biological structures; they maintain the fundamental integrity of cells, compartmentalize regions within them and play an active role in a wide range of cellular processes. Pressure can play a key role in probing the structure and dynamics of membrane assemblies, and is also critical to the biology and adaptation of deep-sea organisms. This article presents an overview of the effect of pressure on the mesostructure of lipid membranes, bilayer organization and lipid–protein assemblies. It also summarizes recent developments in high-pressure structural instrumentation suitable for experiments on membranes.
1. Introduction
Over 70% of the Earth is covered with water, to an average depth of 3.8 km, which exerts a pressure of almost 40 MPa (400 bar). Despite such high pressures, life thrives in the ocean. Indeed, over the past 30 years, pressure-adapted organisms have been discovered in increasingly extreme ocean conditions. The bottom of the Marianas Trench reaches 11 km below sea level, exerting a pressure greater than 100 MPa (1 kbar) (Picard & Daniel, 2013), and even at these pressures adapted bacteria have been found. These organisms must have mechanisms to adapt their lipid membranes to maintain their fundamental structure and mechanical properties (Bartlett, 2002). While high-pressure adaptation is a well established phenomenon (Meersman & McMillan, 2014; Casadei et al., 2002), the regulatory mechanisms employed are poorly understood and are the subject of great interest.
In addition to its direct relevance to the biology of deep-sea organisms, high pressure can play a key role in studying the structure and dynamics of biological assemblies. Hydrostatic pressure can be used to drive structural changes in biomolecules, and offers significant advantages over other structure-change triggers such as temperature and composition changes, both at equilibrium and during rapid changes: high pressure does not tend to disrupt intramolecular bonding below 2 GPa; pressure can be applied and released from a sample extremely rapidly with both increasing and decreasing pressure; and, due to the rapid propagation of pressure, it equilibrates throughout a sample quickly. Many structural changes in membrane assemblies take place on the millisecond to second timescale and so, by using fast pressure jumps, the thermodynamic trigger variable can be decoupled from the structural change, allowing the real-time kinetics and evolution of these changes to be studied using fast-probe techniques.
This review gives an overview of recent advances in high-pressure structural investigations of model membrane assemblies and of some of the recent technology developments that have underpinned these experiments.
2. Effect of pressure on membrane assemblies
Membranes are amongst the most important of all biological structures. In addition to maintaining basic cell integrity and compartmentalization, et al., 2004).
are known to play a vital role in cell signalling, and there is increasing evidence that the micromechanics of membranes help to modulate the activity of the proteins, channels and receptors embedded within them (van den Brink-van der LaanThe structural role of lipid membranes in biology is underpinned by the fact that ) (Fig. 1). These include the fluid lamellar (Lα), two-dimensional hexagonal (HI/HII) and inverse bicontinuous cubic phases (QIIG, QIID, QIIP), and ordered micellar phases (including a number of recently discovered novel ordered inverse micellar structures) (Shearman et al., 2009; Perroni & Mahanthappa, 2013). The structure adopted by a hydrated lipid assembly depends strongly on the preferred curvature of the as well as more subtle effects such as the interplay between curvature, elastic stress and chain-packing frustration (Shearman et al., 2006). All of these factors can be affected by pressure (Seddon et al., 2006).
are molecules and so can self-assemble. form a variety of type I (normal) and type II (inverse) lyotropic liquid crystalline phases when mixed with water (Seddon, 19902.1. Membrane curvature
The effect of pressure on any structure is to drive a reduction in volume (Royer, 1995) and, in lipid assemblies, the net result of increasing pressure is a reduction in hydrocarbon chain motion and a corresponding increase in chain ordering (Skanes et al., 2006). These effects will tend to reduce the cross-sectional area of the lipid hydrocarbon tails. Importantly, the cross-sectional area of the lipid head groups is significantly less sensitive to pressure and so increasing pressure will tend to increase the spontaneous curvature of a lipid monolayer (driving curvature away from the aqueous environment). It should be noted that, for type II (inverse curvature) systems, increasing pressure will cause a reduction in the magnitude of the preferred negative curvature (Shearman et al., 2006).
Moderate increases in pressure will tend to increase the lattice parameter of type 0 (flat) and type II (inverse) fluid lipid mesophases in contact with excess water. There are two distinct contributions to this effect. Firstly, chain ordering will tend to lead to an increase in the lattice parameter, as shown in Fig. 2, although this may be partially offset by isotropic compression of the water that is incorporated into the Secondly, for inverse structures, increasing pressure will cause a reduction in the chain cross-sectional area, which will tend to reduce the magnitude of the negative curvature, leading to a significant increase in the lattice parameter (Fig. 3). This swelling mechanism relies on there being excess water available to flow into the swollen water channels and it is not observed under limited hydration conditions (Tang et al., 2012). The inverse hexagonal HII structure is formed from a hexagonal packing of cylindrical inverse micelles, which leads to chain-packing frustration (Fig. 3), where the lipid chains must adopt different conformations in different parts of the structure. The energy cost of this packing frustration increases at larger lattice parameters and so limits the pressure-induced swelling in HII phases, though they still tend to swell slightly more than lamellar phases. Inverse bicontinuous cubic phases also suffer from packing frustration but to a much lesser extent than HII structures (Seddon & Templer, 1993), and as a result they can swell by as much as 80 Å kbar−1 when subjected to high pressures (Winter et al., 1999).
The effect of pressure on type I (normal curvature) structures is much more difficult to predict, as chain ordering will create a complex interplay between chain extension, which will tend to increase the lattice parameter, and a decrease in the lipid chain cross-sectional area, which will tend to increase the magnitude of the positive interfacial curvature and so reduce the lattice parameter. Very few high-pressure experiments have been carried out on type I curvature lyotropic liquid crystalline phases, but experimental results (Paccamiccio et al., 2006) have demonstrated that pressure can induce a small but significant reduction in the lattice parameter of the Ia3d bicontinuous cubic two-dimensional hexagonal (HI) and Pm3n micellar cubic type I phases exhibited by hydrated dodecyltrimethylammonium chloride (DTAC). In all of these structures a change of around 0.5–1 Å kbar−1 was observed.
Over larger pressure ranges, pressure may also drive phase changes between lipid structures with significantly different interfacial curvature. This will occur when the pressure-induced change in the preferred curvature of the lipid molecules is sufficient to make an alternative phase more energetically favourable. As described above, increasing pressure tends to increase the preferred interfacial curvature for a lipid monolayer and so, for type I systems, pressure will drive phase transitions to structures with larger interfacial curvature (e.g. lamellar to HI). Conversely, type II systems have a negative interfacial curvature, and so pressure drives transitions to structures with a smaller magnitude (more positive) curvature (e.g. HII to lamellar).
Pressure has been seen to drive phase transformations in DTAC from a type I bicontinuous cubic to an HI structure, and from the HI phase to a Pm3n micellar cubic structure (Paccamiccio et al., 2006); in both cases, pressure induces a to a structure with a higher type I curvature.
Pressure-induced phase changes in type II lipid systems have been studied far more widely than type I examples. Pressure has been observed to drive phase transitions between a wide range of type II structures, with pressure always causing a reduction in the magnitude of the interfacial curvature (Tyler et al., 2011; Tang et al., 2012, 2014).
It should be noted that the effect of increasing pressure on the structure of et al., 2011). However, at a phase-transition boundary (where the free energy change, ΔG, for the transition is zero), this relationship can be quantified using the Clapeyron equation [equation (1)] to determine the pressure dependence of a lipid phase-transition temperature, Tt
and lipid assemblies is generally qualitatively similar to the effect of decreasing temperature (Brookswhere ΔSm, ΔHm and ΔVm are the molar transition and volume changes, respectively. These parameters can be measured at, or very near, atmospheric pressure, using (DSC) to determine Tt, ΔSm and ΔHm, and pressure perturbation (PPC) to measure Tt and ΔVm. ΔSm and ΔVm can generally be assumed to be independent of pressure (or to have the same pressure dependence) up to around 200 MPa, and so the Clapeyron equation predicts a linear relationship between transition temperature and pressure.
2.2. Bilayer structure
In addition to their structural role, a key function of biomembranes is to provide an active two-dimensional lipid matrix within which reactions can take place. The dynamic lateral organization and structure in these membranes are thought to play key roles in regulating a wide range of cell processes (Staubach & Hanisch, 2011; Bethani et al., 2010) and pressure can play a key role in investigating this ordering.
As well as influencing the mesoscopic phase behaviour of
pressure can cause more subtle changes in the structure of lipid bilayers and has a significant effect on the micromechanics of membranes. As described above, increasing pressure causes increased hydrocarbon chain ordering and, for flat lipid bilayers, this will tend to lead to an increase in the bilayer thickness, accompanied by a reduction in the area per hydrocarbon chain.High pressures can cause single-component fluid lamellar bilayers, where the hydrocarbon chains are effectively molten, to undergo a et al., 1996; Shaw et al., 2012), where the hydrocarbon chains are now fixed in specific lattice positions in an almost all-trans conformation, and dynamic high-pressure experiments have been used to probe the mechanism of fluid–gel phase transitions (Cheng & Caffrey, 1996). However, even pressure changes that are too small to induce gelling of a fluid bilayer tend to lead to bilayer swelling due to chain extension, with a change in bilayer thickness of less than 2 Å kbar−1.
to a lamellar gel structure (ChengAs mentioned above, lateral structuring in biomembranes, and its effect on protein function and regulation, is thought to be a key property of cellular membranes. Model membranes have been used extensively to gain a valuable insight into lateral ordering in bilayers (Veatch et al., 2004) and pressure is ideally suited to triggering these types of structuring due to the rapid characteristic timescales. In bilayers made from binary mixtures of with different chain melting temperatures (and so, as shown by the Clapeyron equation, different chain melting pressures at a fixed temperature), pressure has been shown to induce between fluid and gel structures (Winter & Jeworrek, 2009). Ternary mixtures of a high-melting-point lipid, low-melting-temperature lipid and cholesterol can exhibit coexistence between two different fluid phases, liquid disordered domains (where the lipid hydrocarbon chains are molten, as in an Lα phase) and liquid ordered (Lo) domains (Veatch et al., 2004) (where the exhibit fast diffusion within the bilayer but the hydrocarbon chains show a high degree of conformational ordering) (Fig. 4). It has recently been shown that pressure can be used to drive liquid–liquid (Nicolini et al., 2006; Jeworrek et al., 2008), and this coexistence can be probed using both small-angle X-ray diffraction and microscopy (Nicolini et al., 2006; Tayebi et al., 2012). There is currently a significant amount of ongoing work aimed at elucidating the biophysical parameters that determine the extent, stability and kinetics of model membrane structuring, and linking this to dynamic ordering in biological membranes. High-pressure and pressure-jump experiments are likely to be extremely important in unlocking the bottlenecks associated with rapid triggering of these types of structural change and have the potential to underpin a wide range of exciting dynamic membrane structural studies.
Changes in the structure of a membrane will inevitably cause changes in the micromechanical properties of the membrane. The fundamental parameters that underpin the micromechanics of a membrane are described by equation (2) for the curvature elastic energy, gc, of a lipid monolayer (Helfrich, 1973)
where H = (c1 + c2) and K = c1c2 are the average mean and Gaussian curvatures, respectively; c1 and c2 are the principal curvatures at a given point on the surface; H0 is the spontaneous mean curvature; and κ and κG are the mean and Gaussian curvature moduli, respectively. The mean curvature modulus describes the energetic cost of changing the mean curvature of a monolayer, whereas the Gaussian modulus represents the energy required to change the Gaussian curvature.
The corresponding parameters can be found for a bilayer: the preferred curvature H0 for a symmetrical bilayer must be zero, and the bilayer bending modulus κb is expected to be simply twice the monolayer modulus (Seddon & Templer, 1993). However, the expression for the bilayer Gaussian modulus, , is more complex (Helfrich & Rennschuh, 1990)
Here, all parameters on the right-hand side refer to a monolayer, including l, the monolayer thickness. κb and refer to the energetic cost of exactly the same physical deformations as described previously for the monolayer.
It has been suggested that pressure increases the monolayer bending modulus (Kawabata et al., 2004) and it is expected that pressure will also increase the bending modulus of a bilayer (Shearman et al., 2006), due to pressure-induced bilayer thickening as discussed earlier. It has been shown that pressure increases the monolayer spontaneous curvature, H0 (Winter et al., 1999). However, it is worth noting that which tend to form inverse structures have a negative spontaneous curvature, so pressure will tend to decrease the magnitude of this negative curvature. The observation that pressure can stabilize bicontinuous cubic lipid phases (Duesing et al., 1997) which have a negative Gaussian curvature suggests that pressure also increases the bilayer Gaussian modulus, (thereby reducing the bilayer curvature elastic energy). However, for which tend to form inverse phases, the effect of pressure on the monolayer Gaussian modulus is far less clear. In equation (3), pressure increases κ but decreases the magnitude of H0, which will tend to cancel out, making it difficult to predict the effect on κG.
2.3. Lipid–protein assemblies
While biological membranes were once thought to consist of active membrane proteins which are associated with a passive lipid structural matrix, it is now known that the protein concentrations can reach as high as 30 wt% in membranes, and both the proteins and ; Bethani et al., 2010).
play a highly active role in cellular processes (Staubach & Hanisch, 2011Lipid–protein interactions have increasingly been recognized as being critical to a range of cellular processes and signalling events, and it is now recognized that ; Charalambous et al., 2012). The overall structural response of biomembranes to external influences such as pressure is likely to result from the close coupling of changes in both the and the proteins, and their interactions. There have so far been relatively few studies of the influence of pressure on model lipid–protein assemblies, but careful control of temperature and pressure has the potential to facilitate future investigation of the mechanisms and dynamics of lipid–protein co-structuring. Two key examples of the effect of pressure on lipid–protein structures are described below.
and membrane proteins must interact strongly both physically and chemically (Lee, 2003Incorporation of the small peripheral membrane protein cytochrome c into inverse bicontinuous cubic lipid phases formed from monoolein has been found to induce significant changes in the structural behaviour of the membrane (Lendermann & Winter, 2003). The incorporation of low concentrations of protein shifts the temperature and pressure phase boundaries for monoolein. At higher protein concentrations, the formation of a noncentrosymmetric cubic phase of P4332 is observed. This structure is thought to be similar to that of the gyroid bicontinuous cubic phase, with one water channel replaced by inverse micelles at the junction points, and with one molecule of cytochrome c positioned in the centre of each suggesting that the lipid–protein interaction drives an increase in the magnitude of the inverse membrane curvature. The pressure stability of this novel structure increases as the protein concentration is increased, which is attributed to attractive protein–lipid headgroup interactions. Pressure-jump X-ray experiments have been used to probe the kinetics of phase transitions in this system (Kraineva et al., 2005) and they show significantly slower transition times than in pure monoolein. Again, this is likely to be due to the attractive lipid–protein interactions and the necessity for co-structuring of the two components.
Monoolein with the integral membrane protein bacteriorhodopsin incorporated (Kulkarni et al., 2013) also shows significantly different pressure–temperature structural behaviour to pure monoolein. Inclusion of the protein increases the pressure stability of the observed bicontinuous cubic structures relative to flat lamellar phases, again suggesting that the protein–lipid interactions present here favour inverse membrane curvature. Highly swollen bicontinuous cubic phases (with lattice parameters of over 200 Å) have been observed at high pressure in these mixtures, both at equilibrium and during pressure-jump X-ray diffraction experiments.
2.4. Pressure-jump kinetic experiments and structural transformation
One of the significant advantages of pressure over other structure-change triggers such as temperature or composition variation is that pressure can be changed extremely quickly: in a number of high-pressure instruments, pressure jumps of several hundred MPa can be performed in 5 ms (Brooks et al., 2010; Woenckhaus et al., 2000), and in some cases pressure jumps can be performed on a sub-microsecond timescale (Dumont et al., 2009) (see below for further discussion of high-pressure technology). Such rapid changes allow the thermodynamic trigger to be decoupled from many biomolecule and membrane assembly structure changes, allowing the out-of-equilibrium behaviour of fast structural transitions in these systems to be characterized.
Pressure jumps have been used to yield valuable information about the kinetics and intermediates involved in the structural transitions of a number of the systems discussed above (Kriechbaum et al., 1993; Conn et al., 2008; Jeworrek et al., 2008; Kulkarni et al., 2013). Recently, a significant advance has been made in quantitative modelling of lipid phase transitions with the development of a kinetic model for lipid structural transitions involving monolayer curvature change (Squires et al., 2009). If a suitable kinetic model can be fitted to describe a the rate at which the transition takes place can be related to the ΔVa
where k(p) and k0 are the rate constants at relative pressure p and atmospheric pressure, respectively, R is the universal and T is the temperature. The can be interpreted using as the difference in volume between the transition state and the volume of the reactants at the same pressure. This can be thought of as an elastic barrier to transformation, in much the same way as the activation energy for a reaction is thought of as a thermal energetic barrier to a reaction.
3. High-pressure instrumentation
As described above, pressure can play a key role in studying the structure of dynamic membrane assemblies and the biology that they underpin. To take full advantage of high-pressure technology, it is essential that it is coupled to fast structure probe techniques, and a great deal of work has been focused on linking high-pressure instrumentation with synchrotron X-ray diffraction and scattering facilities (Woenckhaus et al., 2000; Ando et al., 2008; Krywka et al., 2008; Brooks et al., 2010; Fourme et al., 2012, 2011; Girard et al., 2010). This has also facilitated significant advances in the accessibility of high-pressure instrumentation (Brooks et al., 2010). In addition, high-pressure NMR (Bonev & Morrow, 1997b; Peng & Jonas, 1992), optical microscopy (Nicolini et al., 2006; Vass et al., 2010) and spectroscopy (Schiewek et al., 2007; Dumont et al., 2009) have seen rapid development and provide highly complementary structural data to X-ray experiments.
3.1. High-pressure sample cells for small-angle X-ray scattering (SAXS)
Small-angle X-ray diffraction is ideally suited to probing the structure of lyotropic lipid membrane assemblies, which are ordered on the nanoscale. Additionally, SAXS has been increasingly employed for studying the structures of proteins and protein assemblies (Petoukhov et al., 2012; Tuukkanen & Svergun, 2014).
SAXS high-pressure sample cells have to be carefully designed to hold relatively large sample volumes (several microlitres) at high pressure, while allowing a wide scattering-angle range to be resolved. Within these constraints, SAXS pressure cells have been developed by a number of groups over more than 20 years (So et al., 1992; Mencke et al., 1993; Pressl et al., 1997; Ando et al., 2008; Krywka et al., 2008; Brooks et al., 2010) to address the need for fine pressure control of soft matter systems.
A significant landmark was reached with the development of a robust and versatile cell system by Woenckhaus et al. (2000). This system can perform both static and kinetic pressure experiments in the range 0–0.7 GPa (7 kbar) and −40–100°C. The pressure is generated and controlled via a water-filled hydraulic network that employs two air-operated valves to initiate the pressure jumps, one for jumps of increasing pressure and another for jumps of decreasing pressure. The hydraulic network approach allows pressure jumps to be performed in as little as 5 ms. The cell windows are 0.8 mm thick diamond, eliminating the risk of toxic dust formation associated with beryllium. The specifications of this pressure system have set a benchmark for more recent soft condensed matter pressure cells, and it has facilitated a wide range of high-pressure and pressure-jump experiments on lipid membranes (Conn et al., 2008; Eisenblätter & Winter, 2006; Jeworrek et al., 2008; Kraineva et al., 2005; Tang et al., 2012; Kulkarni et al., 2013).
Recent developments have also been made in sample containment (Ando et al., 2008), windows with low parasitic scatter (Wang et al., 2012) and sample-loading ports (Krywka et al., 2008). The development of a dedicated sample-loading port (in contrast with previous cells, which generally required samples to be loaded through one of the X-ray window ports) has the significant advantage of allowing accurate subtraction of background scattering due to the X-ray windows.
We have recently developed a high-pressure SAXS system based at beamline I22, Diamond Light Source, UK (Brooks et al., 2010). Static and millisecond pressure-jump experiments can be carried out in the range 0.1–500 MPa and between −20 and 120°C. The system is fully automated, integrated with the beamline and available to all users of I22, which opens up high-pressure technology to an extremely wide user base.
3.2. Diamond anvil cells (DACs)
Diamond anvil cells (Katrusiak, 2008) are routinely employed for high-pressure experiments requiring pressure up to 100 GPa (105 bar). They consist of two opposing anvils which compress a sample held in a metal gasket. The simplest DACs apply a relatively small pressure to the diamonds via a screw system, and this pressure is intensified by the shape of the diamond and applied to the sample. Significant advances have recently been made in the design of DACs, particularly with the development of gas-membrane-driven cells, where a gas-filled `balloon' applies the initial pressure, instead of a screw-driven brace. This has several advantages, including remote operation, the ability to apply small controlled pressure increments, and higher achievable pressures due to the absence of screw friction. The internal volume of a DAC is very small and so pressure measurements are usually made by placing a small ruby or α-quartz crystal in the sample and measuring the position of the R1 ruby fluorescence maximum (Piermarini et al., 1975) or quartz IR vibration (Wong et al., 1985), which shift with pressure, offering a resolution of around 20 MPa (Czeslik et al., 1998). There has been significant interest recently in developing alternative pressure transducers for use in DACs with increased resolution (Oger et al., 2006; Picard et al., 2006).
DACs have proved extremely valuable in studying protein behaviour at high pressure (Silva et al., 2001). While the pressures accessible with DACs are often significantly higher than required to study membrane structure changes, lipid studies have been carried out at up to 2 GPa (Czeslik et al., 1998; Reis & Winter, 1998) and recent advances, particularly in pressure detection (Picard et al., 2006) and control (Oger et al., 2006), may open up new avenues in very high-pressure lipid and membrane research. A significant advantage of DACs over the soft matter SAXS cells described above is that far wider diffraction angles can be resolved, since the diamond anvils are relatively X-ray transparent. DAC experiments have proved particularly valuable in macromolecular crystallography (Fourme et al., 2012) and this technique is now widely available at synchrotron beamlines offering extreme conditions (Fourme et al., 2011).
3.3. Complementary high-pressure structure probe techniques
3.3.1. High-pressure NMR
Several high-pressure NMR systems have been reported (Fourme et al., 2012). However, the high-pressure NMR probe developed by Bonev & Morrow (1997b) was designed specifically for use with soft matter and has been used extensively to study model membrane samples (Bonev & Morrow, 1997a; Fiech et al., 1998). This probe allows studies up to 300 MPa at temperatures between −20 and 100°C.
3.3.2. High-pressure optical microscopy
There have been exciting recent developments in the design and use of high-pressure optical microscopy systems, allowing bright-field (Frey et al., 2006; Nishiyama & Kojima, 2012), polarizing (Reck et al., 1998), fluorescence (Nicolini et al., 2006; Vass et al., 2010; Nishiyama et al., 2009) and single-molecule (Vass et al., 2013) microscopy, at pressures as high as 700 MPa (Vass et al., 2010). A number of these cells have again been based on similar design principles to the soft matter SAXS cells described above (Reck et al., 1998). However, there has also been a very successful optical pressure cell constructed from narrow-bore fused silica capillary tubing (Nicolini et al., 2006). A significant consideration for high-resolution microscopy is allowing close access of the microscope objective lens to the sample while maintaining the pressure stability of the cell. The working distance of objective lenses falls as their magnification increases, but magnification of up to 40× has been achieved using a metal body/window type cell (Frey et al., 2006; Nishiyama et al., 2009), and 63× using the capillary tube system mentioned above (Nicolini et al., 2006).
3.3.3. Spectroscopy pressure cells
A number of high-pressure soft matter cells have been developed for use with Fourier-transform IR (FT–IR) spectroscopy, following a similar design to the soft matter SAXS cells above (Schiewek et al., 2007) and using a hydraulic network to generate pressure. These have been used at static pressures up to 600 MPa and for pressure jumps (Schiewek et al., 2007). In addition, DACs have been used successfully for FT–IR experiments (Czeslik et al., 1998).
The speed of pressure jumps generated by a hydraulic valve system as described above is limited to around 5 ms by the time required to open the pressure-jump valve. While this is considerably faster than many biomolecular transformations, some structure changes (particularly protein structure changes) can occur on a shorter timescale, which has driven the development of faster pressure-jump technology.
Spectroscopy pressure cells have been developed with a piezoelectric stack piston built into the cell body (Pearson et al., 2002) that can generate extremely fast pressure jumps. Although the movement of the piston limits the pressure that can be reached, jumps of up to 20 MPa can be performed in 150 µs while probing the sample by absorption or fluorescence spectroscopy.
Burst diaphragms have been used for many years to generate rapid downward pressure jumps (Davis & Gutfreund, 1976) but there has recently been a significant advance in burst-membrane technology with the development of an electrically ruptured burst diaphragm (Dumont et al., 2009). This allows the rupture to be induced at an accurately set pressure, and downward pressure jumps of up to 250 MPa can be performed in less than 700 ns, providing the fastest pressure jumps currently available.
4. Concluding remarks
High pressure has proved to be an extremely powerful biophysical tool for studying the structural behaviour of membrane assemblies. It has facilitated investigation of the mechanisms of large-scale structure changes in lipid mesophases, the kinetics of
and ordering with bilayers, and the stability of lipid–protein assemblies, amongst a wide variety of other experiments. Developments in high-pressure instrumentation continue to widen the scope of pressure technology, both in terms of the samples that it can be applied to and the groups that can make use of it. With exciting new developments such as ultra-fast pressure-jump technology and high-resolution high-pressure microscopy, there will clearly be a wide range of experiments in the near future which will provide ever greater insight into the structure and function of dynamic biological membranes.References
Ando, N., Chenevier, P., Novak, M., Tate, M. W. & Gruner, S. M. (2008). J. Appl. Cryst. 41, 167–175. Web of Science CrossRef CAS IUCr Journals Google Scholar
Bartlett, D. H. (2002). Biochim. Biophys. Acta Protein Struct. Mol. Enzymol. 1595, 367–381. CrossRef CAS Google Scholar
Bethani, I., Skånland, S. S., Dikic, I. & Acker-Palmer, A. (2010). EMBO J. 29, 2677–2688. CrossRef CAS PubMed Google Scholar
Bonev, B. B. & Morrow, M. R. (1997a). Phys. Rev. E, 55, 5825–5833. CrossRef CAS Google Scholar
Bonev, B. B. & Morrow, M. R. (1997b). Rev. Sci. Instrum. 68, 1827–1830. CrossRef CAS Google Scholar
van den Brink-van der Laan, E., Killian, J. A. & de Kruijff, B. (2004). Biochim. Biophys. Acta Biomembranes, 1666, 275–288. CAS Google Scholar
Brooks, N. J., Ces, O., Templer, R. H. & Seddon, J. M. (2011). Chem. Phys. Lipids, 164, 89–98. Web of Science CrossRef CAS PubMed Google Scholar
Brooks, N. J., Gauthe, B. L., Terrill, N. J., Rogers, S. E., Templer, R. H., Ces, O. & Seddon, J. M. (2010). Rev. Sci. Instrum. 81, 064103. CrossRef PubMed Google Scholar
Casadei, M. A., Manas, P., Niven, G., Needs, E. & Mackey, B. M. (2002). Appl. Environ. Microbiol. 68, 5965–5972. CrossRef PubMed CAS Google Scholar
Charalambous, K., Booth, P. J., Woscholski, R., Seddon, J. M., Templer, R. H., Law, R. V., Barter, L. M. & Ces, O. (2012). J. Am. Chem. Soc. 134, 5746–5749. Web of Science CrossRef CAS PubMed Google Scholar
Cheng, A. C. & Caffrey, M. (1996). J. Phys. Chem. 100, 5608–5610. CrossRef CAS Web of Science Google Scholar
Cheng, A. C., Mencke, A. & Caffrey, M. (1996). J. Phys. Chem. 100, 299–306. CrossRef CAS Web of Science Google Scholar
Conn, C. E., Ces, O., Squires, A. M., Mulet, X., Winter, R., Finet, S. M., Templer, R. H. & Seddon, J. M. (2008). Langmuir, 24, 2331–2340. Web of Science CrossRef PubMed CAS Google Scholar
Czeslik, C., Reis, O., Winter, R. & Rapp, G. (1998). Chem. Phys. Lipids, 91, 135–144. Web of Science CrossRef CAS Google Scholar
Davis, J. S. & Gutfreund, H. (1976). FEBS Lett. 72, 199–207. CrossRef PubMed CAS Web of Science Google Scholar
Duesing, P. M., Seddon, J. M., Templer, R. H. & Mannock, D. A. (1997). Langmuir, 13, 2655–2664. CrossRef CAS Web of Science Google Scholar
Dumont, C., Emilsson, T. & Gruebele, M. (2009). Nat. Methods, 6, 515–519. CrossRef PubMed CAS Google Scholar
Eisenblätter, J. & Winter, R. (2006). Biophys. J. 90, 956–966. Web of Science PubMed Google Scholar
Fiech, D. C., Bonev, B. B. & Morrow, M. R. (1998). Phys. Rev. E, 57, 3334–3343. CrossRef CAS Google Scholar
Fourme, R., Girard, E. & Akasaka, K. (2012). Curr. Opin. Struct. Biol. 22, 636–642. Web of Science CrossRef CAS PubMed Google Scholar
Fourme, R., Girard, E., Dhaussy, A.-C., Medjoubi, K., Prangé, T., Ascone, I., Mezouar, M. & Kahn, R. (2011). J. Synchrotron Rad. 18, 31–36. Web of Science CrossRef CAS IUCr Journals Google Scholar
Frey, B., Hartmann, M., Herrmann, M., Meyer-Pittroff, R., Sommer, K. & Bluemelhuber, G. (2006). Microsc. Res. Technol. 69, 65–72. CrossRef Google Scholar
Girard, E., Fourme, R., Ciurko, R., Joly, J., Bouis, F., Legrand, P., Jacobs, J., Dhaussy, A.-C., Ferrer, J.-L., Mezouar, M. & Kahn, R. (2010). J. Appl. Cryst. 43, 762–768. Web of Science CrossRef CAS IUCr Journals Google Scholar
Helfrich, W. (1973). Z. Naturforsch. Teil C, C 28, 693–703. Google Scholar
Helfrich, W. & Rennschuh, H. (1990). J. Phys. (Paris), 51, C7189–C7195. CrossRef Google Scholar
Jeworrek, C., Pühse, M. & Winter, R. (2008). Langmuir, 24, 11851–11859. Web of Science CrossRef PubMed CAS Google Scholar
Katrusiak, A. (2008). Acta Cryst. A64, 135–148. Web of Science CrossRef CAS IUCr Journals Google Scholar
Kawabata, Y., Nagao, M., Seto, H., Komura, S., Takeda, T., Schwahn, D., Yamada, N. L. & Nobutou, H. (2004). Phys. Rev. Lett. 92, 056103. Web of Science CrossRef PubMed Google Scholar
Kraineva, J., Narayanan, R. A., Kondrashkina, E., Thiyagarajan, P. & Winter, R. (2005). Langmuir, 21, 3559–3571. Web of Science CrossRef PubMed CAS Google Scholar
Kriechbaum, M., Osterberg, F., Tate, M. W., Shyamsunder, E., Polcyn, A. D., So, P. T. C. & Gruner, S. M. (1993). Biophys. J. 64, A296–A296. Google Scholar
Krywka, C., Sternemann, C., Paulus, M., Tolan, M., Royer, C. & Winter, R. (2008). ChemPhysChem, 9, 2809–2815. Web of Science CrossRef PubMed CAS Google Scholar
Kulkarni, C. V., Ces, O., Templer, R. H. & Seddon, J. M. (2013). Soft Matter, 9, 6525–6531. CrossRef CAS Google Scholar
Lee, A. (2003). Biochim. Biophys. Acta Biomembranes, 1612, 1–40. CrossRef CAS Google Scholar
Lendermann, J. & Winter, R. (2003). Phys. Chem. Chem. Phys. 5, 1440–1450. Web of Science CrossRef CAS Google Scholar
Meersman, F. & McMillan, P. F. (2014). Chem. Commun. 50, 766–775. CrossRef CAS Google Scholar
Mencke, A., Cheng, A. & Caffrey, M. (1993). Rev. Sci. Instrum. 64, 383–389. CrossRef CAS Google Scholar
Nicolini, C., Celli, A., Gratton, E. & Winter, R. (2006). Biophys. J. 91, 2936–2942. Web of Science CrossRef PubMed CAS Google Scholar
Nishiyama, M., Kimura, Y., Nishiyama, Y. & Terazima, M. (2009). Biophys. J. 96, 1142–1150. Web of Science CrossRef PubMed CAS Google Scholar
Nishiyama, M. & Kojima, S. (2012). Int. J. Mol. Sci. 13, 9225–9239. CrossRef PubMed Google Scholar
Oger, P. M., Daniel, I. & Picard, A. (2006). Biochim. Biophys. Acta Proteins Proteomics, 1764, 434–442. CrossRef CAS Google Scholar
Paccamiccio, L., Pisani, M., Spinozzi, F., Ferrero, C., Finet, S. & Mariani, P. (2006). J. Phys. Chem. B, 110, 12410–12418. CrossRef PubMed CAS Google Scholar
Pearson, D. S., Holtermann, G., Ellison, P., Cremo, C. & Geeves, M. A. (2002). Biochem. J. 366, 643–651. CrossRef PubMed CAS Google Scholar
Peng, X. & Jonas, J. (1992). Biochemistry, 31, 6383–6390. CrossRef PubMed CAS Web of Science Google Scholar
Perroni, D. V. & Mahanthappa, M. K. (2013). Soft Matter, 9, 7919–7922. Web of Science CrossRef CAS Google Scholar
Petoukhov, M. V., Franke, D., Shkumatov, A. V., Tria, G., Kikhney, A. G., Gajda, M., Gorba, C., Mertens, H. D. T., Konarev, P. V. & Svergun, D. I. (2012). J. Appl. Cryst. 45, 342–350. Web of Science CrossRef CAS IUCr Journals Google Scholar
Picard, A. & Daniel, I. (2013). Biophys. Chem. 183, 30–41. Web of Science CrossRef CAS PubMed Google Scholar
Picard, A., Oger, P. M., Daniel, I., Cardon, H., Montagnac, G. & Chervin, J. C. (2006). J. Appl. Phys. 100, 034915. Web of Science CrossRef Google Scholar
Piermarini, G. J., Block, S., Barnett, J. D. & Forman, R. A. (1975). J. Appl. Phys. 46, 2774. CrossRef Web of Science Google Scholar
Pressl, K., Kriechbaum, M., Steinhart, M. & Laggner, P. (1997). Rev. Sci. Instrum. 68, 4588–4592. CrossRef CAS Google Scholar
Reck, T., Sautter, E., Dollhopf, W. & Pechhold, W. (1998). Rev. Sci. Instrum. 69, 1823–1827 CrossRef CAS Google Scholar
Reis, O. & Winter, R. (1998). Langmuir, 14, 2903–2909. Web of Science CrossRef CAS Google Scholar
Royer, C. A. (1995). Methods in Enzymology, Vol. 259. Energetics of Biological Macromolecules, edited by M. Johnson, G. Ackers, J. Abelson & M. Simon, pp. 357–377. San Diego: Academic Press Inc. Google Scholar
Schiewek, M., Krumova, M., Hempel, G. & Blume, A. (2007). Rev. Sci. Instrum. 78, 045101. CrossRef PubMed Google Scholar
Seddon, J. M. (1990). Biochim. Biophys. Acta, 1031, 1–69. CrossRef CAS PubMed Web of Science Google Scholar
Seddon, J. M., Squires, A. M., Conn, C. E., Ces, O., Heron, A. J., Mulet, X., Shearman, G. C. & Templer, R. H. (2006). Philos. Trans. R. Soc. London Ser. A, 364, 2635–2655. CrossRef CAS Google Scholar
Seddon, J. M. & Templer, R. H. (1993). Philos. Trans. R. Soc. London Ser. A, 344, 377–401. CrossRef CAS Google Scholar
Shaw, K. P., Brooks, N. J., Clarke, J. A., Ces, O., Seddon, J. M. & Law, R. V. (2012). Soft Matter, 8, 1070–1078. CrossRef CAS Google Scholar
Shearman, G. C., Ces, O., Templer, R. H. & Seddon, J. M. (2006). J. Phys. Condens. Matter, 18, s1105–S1124. Web of Science CrossRef CAS PubMed Google Scholar
Shearman, G. C., Tyler, A. I., Brooks, N. J., Templer, R. H., Ces, O., Law, R. V. & Seddon, J. M. (2009). J. Am. Chem. Soc. 131, 1678–1679. Web of Science CrossRef PubMed CAS Google Scholar
Silva, J. L., Foguel, D. & Royer, C. A. (2001). Trends Biochem. Sci. 26, 612–618. Web of Science CrossRef PubMed CAS Google Scholar
Skanes, I. D., Stewart, J., Keough, K. M. W. & Morrow, M. R. (2006). Phys. Rev. E, 74, 051913. CrossRef Google Scholar
So, P. T. C., Gruner, S. M. & Shyamsunder, E. (1992). Rev. Sci. Instrum. 63, 1763–1770. CrossRef Google Scholar
Squires, A. M., Conn, C. E., Seddon, J. M. & Templer, R. H. (2009). Soft Matter, 5, 4773–4779. CrossRef CAS Google Scholar
Staubach, S. & Hanisch, F. G. (2011). Expert Rev. Proteomics, 8, 263–277. CrossRef CAS PubMed Google Scholar
Tang, T. Y. D., Brooks, N. J., Jeworrek, C., Ces, O., Terrill, N. J., Winter, R., Templer, R. H. & Seddon, J. M. (2012). Langmuir, 28, 13018–13024. Web of Science CrossRef CAS PubMed Google Scholar
Tang, T. Y. D., Seddon, A. M., Jeworrek, C., Winter, R., Ces, O., Seddon, J. M. & Templer, R. H. (2014). Soft Matter, 10, 3009–3015. CrossRef CAS PubMed Google Scholar
Tayebi, L., Ma, Y. C., Vashaee, D., Chen, G., Sinha, S. K. & Parikh, A. N. (2012). Nat. Mater. 11, 1074–1080. Web of Science CAS PubMed Google Scholar
Tuukkanen, A. T. & Svergun, D. I. (2014). FEBS J. 281, 1974–1987. CrossRef CAS PubMed Google Scholar
Tyler, A. I. I., Shearman, G. C., Brooks, N. J., Delacroix, H., Law, R. V., Templer, R. H., Ces, O. & Seddon, J. M. (2011). Phys. Chem. Chem. Phys. 13, 3033–3038. Web of Science CrossRef CAS PubMed Google Scholar
Vass, H., Black, S. L., Herzig, E. M., Ward, F. B., Clegg, P. S. & Allen, R. J. (2010). Rev. Sci. Instrum. 81, 053710. CrossRef PubMed Google Scholar
Vass, H., Black, S. L., Flors, C., Lloyd, D., Ward, F. B. & Allen, R. J. (2013). Appl. Phys. Lett. 102, 154103. Web of Science CrossRef Google Scholar
Veatch, S. L., Polozov, I. V., Gawrisch, K. & Keller, S. L. (2004). Biophys. J. 86, 2910–2922. Web of Science CrossRef PubMed CAS Google Scholar
Wang, S., Meng, Y., Ando, N., Tate, M., Krasnicki, S., Yan, C., Liang, Q., Lai, J., Mao, H., Gruner, S. M. & Hemley, R. J. (2012). J. Appl. Cryst. 45, 453–457. Web of Science CrossRef CAS IUCr Journals Google Scholar
Winter, R., Erbes, J., Templer, R. H., Seddon, J. M., Syrykh, A., Warrender, N. A. & Rapp, G. (1999). Phys. Chem. Chem. Phys. 1, 887–893. Web of Science CrossRef CAS Google Scholar
Winter, R. & Jeworrek, C. (2009). Soft Matter, 5, 3157–3173. CrossRef CAS Google Scholar
Woenckhaus, J., Köhling, R., Winter, R., Thiyagarajan, P. & Finet, S. (2000). Rev. Sci. Instrum. 71, 3895–3899. CrossRef CAS Google Scholar
Wong, P. T. T., Moffatt, D. J. & Baudais, F. L. (1985). Appl. Spectrosc. 39, 733–735. CrossRef CAS Web of Science Google Scholar
This is an open-access article distributed under the terms of the Creative Commons Attribution (CC-BY) Licence, which permits unrestricted use, distribution, and reproduction in any medium, provided the original authors and source are cited.