research papers
Direct LiF imaging diagnostics on refractive X-ray focusing at the EuXFEL High Energy Density instrument
aJoint Institute for High Temperatures Russian Academy of Sciences, Izhorskaya St 13, Bd 2, Moscow 125412, Russian Federation, bEuropean XFEL, Holzkoppel 4, 22869 Hamburg, Germany, cInstitute for Open and Transdisciplinary Research Initiatives, Osaka University, 2-6 Yamadaoka, Osaka 565-0871, Japan, dGraduate School of Engineering, Osaka University, Suita, Osaka 565-0871, Japan, ePhoton Pioneers Center, Osaka University, Suita, Osaka 565-0871, Japan, fDepartment of Earth and Environmental Sciences, Università degli Studi di Milano-Bicocca, Piazza della Scienza 4, 20126 Milan, Italy, gDepartment of Radiation and Chemical Physics, Institute of Physics, Czech Academy of Sciences, Na Slovance 2, 182 21 Prague 8, Czech Republic, hPlasma Physics Department, Institute of Plasma Physics, Czech Academy of Sciences, Za Slovankou 3, 182 00 Prague 8, Czech Republic, and iSLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, CA 94025, USA
*Correspondence e-mail: seomakarov28@gmail.com, spikuz@gmail.com
The application of fluorescent crystal media in wide-range X-ray detectors provides an opportunity to directly image the spatial distribution of ultra-intense X-ray beams including investigation of the focal spot of free-electron lasers. Here the capabilities of the micro- and nano-focusing X-ray refractive optics available at the High Energy Density instrument of the European XFEL are reported, as measured in situ by means of a LiF fluorescent detector placed into and around the beam caustic. The intensity distribution of the beam focused down to several hundred nanometers was imaged at 9 keV photon energy. A deviation from the parabolic surface in a stack of nanofocusing Be compound refractive lenses (CRLs) was found to affect the resulting intensity distribution within the beam. Comparison of experimental patterns in the far field with patterns calculated for different CRL lens imperfections allowed the overall inhomogeneity in the CRL stack to be estimated. The precise determination of the focal spot size and shape on a sub-micrometer level is essential for a number of high energy density studies requiring either a pin-size backlighting spot or extreme intensities for X-ray heating.
Keywords: X-ray free-electron lasers; X-ray focusing; X-ray beam characterization; compound refractive lenses; focusing system; lithium fluoride (LiF) detector.
1. Introduction
The recent development of X-ray free-electron laser (FEL) technology opens the door for experimental physics of high-energy photon–matter interactions and great opportunities for advanced technology in material processing. State-of-the-art FEL facilities have recently been commissioned: LCLS (USA, 2009), SACLA (Japan, 2011), PAL-XFEL (Republic of Korea, 2016), SwissFEL (Switzerland, 2016), EuXFEL (Germany, 2017). The radiation provided by XFELs possesses most of the important features of lasing, such as coherency, narrow bandwidth, and close to diffraction-limited angular divergence. With up to a few mJ pulse energy, tight focusing and a few femtosecond 20 W cm−2 are now within reach. A wide range of possible parameters for XFEL beams (wavelength, energy) makes it possible to study various processes in matter that occur under the influence of X-rays. In addition to that, focused beams of ultrahigh intensity can be used to develop new technological applications for nanoscale precise material processing with X-rays. Precise knowledge of the profile at the interaction area is apparently crucial for any FEL experiment.
radiation fields with extremely high intensity up to 10Since XFELs began to operate, many operational and autonomous methods have traditionally been used to monitor the wave properties of the beam. These include out of focus diagnostics (diagnostics performed away from the beam focus) such as Shack–Hartmann sensors (Keitel et al., 2016), Young's experiment with two slits (Vartanyants et al., 2011), crystal spectrometry (Boesenberg et al., 2017), speckle tracking (Berujon et al., 2015), ptychography (Schropp et al., 2013) and various grating-based methods (Makita et al., 2020; Daurer et al., 2021; Rutishauser et al., 2012; Schneider et al., 2018; Liu et al., 2018); and, on the other hand, the traditionally practiced in focus methods (diagnostics at the focusing area) such as ablation imprinting (Chalupsky et al., 2011, 2015) and the widely used knife-edge scanning approach (Yumoto et al., 2013). Each of these methods has its own advantages and disadvantages.
In this work we applied imaging diagnostics based on in situ measurement of the intensity distribution by means of a lithium fluoride (LiF) crystal detector placed directly in the part of the beam under interest. The performance of this method in terms of characterizing the focusability and spatial structure of the XFEL beams has been demonstrated by Pikuz et al. (2015, 2018), where the possibility of recording the of the intensity profile of the XFEL beam with high spatial resolution (∼1 µm), very large (no less than 106) and within a field of view larger than a few mm2 at a photon energy of 10 keV was shown. The combination of the significantly advantageous characteristics of the LiF detector represents a unique feature compared with conventional detectors such as image plates and CCDs. Makarov et al. (2020) observed the 2D intensity distribution of a diffraction pattern created by the PETRA-III X-ray beam with circular aperture up to the 16th order maximum, which required both a spatial resolution in the sub-micrometer range and a of ∼107. The micrometer-size resolution of the LiF detector allowed the characterization of the SACLA XFEL source and determination of the spatial and coherent properties of the beam by applying the high-resolution Fresnel diffraction method developed by Ruiz-Lopez et al. (2017). In this way, LiF as an in situ imaging detector is a very convenient instrument for acquiring intensity distribution patterns along the caustics of XFEL beams in any configuration: free-propagated direct beam or beam transformed by the X-ray focusing system. Thus, the focusing properties of the Kirkpatrick–Baez mirrors installed at BL3 of SACLA XFEL have been studied (Pikuz et al., 2015).
At present, in experiments with XFELs, refractive focusing systems are used (Hagemann et al., 2021; Maeda et al., 2020; Seiboth et al., 2018; Schropp et al., 2015). Our work was done within the framework of the multi-approach experiment on the complex characterization of the refractive focusing system installed at the High Energy Density (HED) instrument at the EuXFEL (Schenefeld, Germany). Details of the whole campaign performed with the application of various diagnostics methods, including those mentioned above, is the subject of a special publication and will be described elsewhere. Here we report on imaging of the hard X-ray focus by means of in situ acquisition of XFEL patterns with a LiF detector and on the results of simulations that support our initial experimental observations.
2. Experimental method
The experiment was carried out at the HED instrument, which is located at the SASE2 undulator. The X-ray beam transport from the undulator up to the HED experimental hutch is schematically shown in Fig. 1 [a detailed description of the X-ray transport optics is given by Zastrau et al. (2021)]. The X-ray focusing system of the HED instrument is based entirely on the use of a beryllium compound refractive lens (CRL) with parabolic surfaces of individual refractive lenses. The CRL is chromatic, and thus requires different lens configurations for different photon energies.
Four CRL lens units (1–4) can be used to focus the beam at different positions along the HED beamline (Zastrau et al., 2021; Schneidmiller & Yurkov, 2011). In our experiment, the SASE2 undulator was tuned to deliver short X-ray pulses of ∼40 fs duration and peak pulse energy of ∼2 mJ at a photon energy of 9 keV. Beam characterization and quality assessments were performed for the beam focused using the third lens unit (CRL3) to a focal spot of several micrometers in waist, and for the beam focused using the fourth lens unit (CRL4) to a focal spot of sub-micrometer size. In both cases the focusing was provided in combination with the most upstream lens unit (CRL1) in the tunnel. The lens unit CRL1 is the most upstream focusing element on the beam transport line and can be used for collimation, direct focusing and intermediate focusing of the XFEL beam to CRL2 and CRL3. Table 1 shows the main parameters of the lenses used in the experiment. The diffraction-limited size of the beam in the focus, d = λ/NA, where λ is the wavelength and NA is the numerical aperture of the CRL, was ∼1.5 µm for CRL3 and ∼200 nm for CRL4 at 9 keV photon energy.
|
To study the focusing properties of lenses, it is necessary to know the intensity distribution within the beam not only at the focal plane but also at a distance along the laser propagation axis. The 3D spatial profile of the focused beam is bound by the surface of the caustic. The caustic of a Gaussian beam after focusing by an ideal optical system represents a hyperbolic surface. The angle between the asymptotes of the hyperbola defines the divergence of the beam. The position and the diameter of the waist define the position and the size of the focus. The distribution of radiation in the rz (FWHM of the beam intensity on-axis) at distance z from the focal plane can be calculated using the equation (Self, 1983)
of the caustic is well approximated by the Gaussian function. Following the theory of focused Gaussian beams, the spot diameter 2where r0 is the spot radius of the beam at the focal plane, zR is the Rayleigh range, λ is the wavelength of the photon and M2 is the beam quality factor.
To reveal the caustic of a focused beam, we used a LiF detector. The formation of images in a LiF detector crystal is based on the ability to create stable color centers (CCs) in the crystal under direct irradiation by photons with energy greater than 14 eV, whose absorption and fluorescence spectra belong to the optical range (Baldacchini et al., 2005). This allows LiF to be used as a detector in which the image is encoded according to the density of the color centers in the crystal. Deep propagation of the X-ray beam into the LiF causes generation of CCs in the volume of the LiF crystal and allows the 3D structure of the beam to be visualized, for example for precise determination of the best focal position (Pikuz et al., 2015). It should also be noted that the spatial resolution of the LiF detector depends on the photon energy. The reason for this is the influence of the secondary electron cascade generated in LiF by incident X-ray photons. In the work by Grum-Grzhimailo et al. (2017), it was theoretically predicted that the radius of the electron cloud for hard X-ray photons can reach several hundred nanometers.
In our experiment, we used circular LiF crystals of 20 mm diameter and 2 mm thickness mounted on an XYZ motorized stage. By moving a crystal along the X-ray beam (Z-axis), the intensity distribution in the of the beam was recorded in sequences of planes XY near the focus over a Z-range of ∼300 mm, with a step size from 0.2 mm up to 2 mm (Fig. 1). The photoluminescent (PL) signal of the exposed LiF crystals was read out using a laser scanning confocal microscope (Carl Zeiss LSM700). To obtain a 2D image of the beam in values of intensity, the PL signal was recalculated by means of an algorithm developed by Bonfigli et al. (2021). It is known that the PL response of the LiF crystal depends only on the amount of absorbed energy in the crystal and does not depend on the energy of incident photons. In our calculation we applied the PL response function defined in recent works (Mabey et al., 2019; Makarov et al., 2020). This function was determined in a wide enough range of absorbed energies to be applicable for our experimental conditions.
3. Experimental results and discussion
3.1. Focusing properties of lens unit CRL1
At first, the X-ray beam spatial profile was characterized only with the upstream lens unit CRL1. The diffraction-limited monochromatic X-ray beam size with the CRL1 unit is ∼150–250 µm at interaction chamber 1 (IC1) (Zastrau et al., 2021). In our experiment, the beam was directly focused to IC1. In Fig. 2, an image of the beam measured at a photon energy of 9 keV is presented. It can be clearly seen that the beam size is consistent with theoretical considerations; however, the intensity profiles taken across vertical and horizontal directions has a small astigmatism with ratio FWHMhoriz/FWHMvert = 160 µm/190 µm = 0.84 and the base of the intensity profile in the vertical direction is broader compared with the Gaussian one. The observed loss of the waist symmetry and spreading of the shape can be caused by mirror clipping due to beam drift and/or slight geometrical imperfections of the lens.
3.2. X-ray focus characterization after CRL3
To characterize the intensity distribution of the focused beam, the caustic was imaged in different planes along the beam propagation for different focusing conditions. The expected focal point was at Z = 0 mm. Fig. 3 shows sequences of LiF images recorded in a Z range of 240 mm for different sets of CRL1 and CRL3 units. In run #58 we clearly observe a double structure of the X-ray beam that diverges horizontally over the entire Z range. This indicates that single elements in the stack CRL3 were most likely misaligned or damaged. Indeed, by consequentially removing the elements one by one from the CRL3 stack, we found that the CRL3 unit provides a much better beam profile without the last lens cartridge (run #67). The beam has less astigmatism in comparison with run #58 and the double beam structure is gone. It is suspected that there may be some damage on the last element. The best intensity distribution in the beam was obtained in run #84 by the additional change of elements in CRL1 (see Fig. 3). At best the beam diameter in the focal plane (Z = 0 mm) was found to be 3.4 µm and 3.7 µm at the FWHM signal level in the vertical and horizontal directions, respectively [Figs. 4(a) and 4(b)]. By applying the PL response function to the LiF image obtained in the focal plane, it was found that about 50% of the energy is contained at a FWHM that agrees with the Gaussian intensity distribution inside the beam.
In addition, a comparison of the experimental beam caustic near the focal plane with the calculated one is presented in Figs. 4(c) and 4(d). The black dots show the measured spot sizes. Positive parts of the error bars correspond to the statistical error in determining the size of the spot which does not have a perfectly round shape. It should be emphasized that the measured distribution in the LiF images may be blurred by the secondary photoelectron cloud. In this case, the actual spot diameter is smaller than obtained as discussed in Section 2. Therefore, we introduce an error that determines the order of magnitude of the measurement uncertainty of the beam size in the negative part. Our estimates for the radius of the photoelectron cloud come from both theoretical estimates (Grum-Grzhimailo et al., 2017) and experimental measurements, which showed that the magnitude of this value does not exceed 300 nm. This value was taken into account by increasing a negative part of the error bars for the experimental points in Figs. 4(c) and 4(d). We found that the best fit of the experimental points in the vertical plane occurs in the case of ZR = 175 mm and M2 = 1.1 [olive solid curve in Fig. 4(c)]. From this point we can conclude that the real beam profile is not ideally Gaussian while the quality factor M2 is not significantly different to 1. However, as can be seen in Fig. 4(d), the caustic in the horizontal plane does not look like a hyperbola and is evidently different from an ideal Gaussian. This most likely originates due to the lens errors, and possible clipping of the beam.
3.3. X-ray sub-micrometer focus characterization after CRL4
For some experimental applications the X-ray beam should be focused down to several tens of nanometers. To achieve such a tightly focused beam, the HED instrument is equipped with the CRL4 unit consisting of a stack of short focal length units (focal distances in the range 100–1000 mm are available), contributed by the Helmholtz International Beamline for Extreme Fields (HIBEF) user consortium (https://www.hibef.eu). The CRL4 unit is installed inside the IC1 experimental chamber due to the short focal distance. In this work, we used a CRL4 stack that provided a focal length of ∼300 mm at a photon energy of 9 keV. The expected size of the waist in the focal plane is of the order of 200 nm. This also involves using a custom-produced phase-correction plate. Details of the phase-correction plate are given by Seiboth et al. (2017).
Fig. 5 shows the intensity distribution of the focused X-ray beam measured by the LiF detector at sequences of planes near the expected focal point. As can be seen in the PL images, the X-ray beam is focused to the point Z = 0 mm and then diverges. Due to high sensitivity and large of the LiF detector, it was possible without attenuation to measure both the intensity profile of the entire beam far out of focus and in the waist region, where the signal increases by several orders of magnitude. We want to draw attention to the intensity distribution within the cross sections of the focused beam. An interesting evolution of the beam spatial profile was observed along the beam propagation. It is seen in Fig. 5 that a dark spot in the central part of the beam intensity distribution upstream of the focal position (Z < 0) is transformed to a hot spot spike in the same area after the focus position (Z > 0). This indicates that Be lenses as the elements of the CRL4 stack have geometrical imperfection. Such structure of the beam distribution can appear due to deviations of the Be lens refractive surface from the ideal parabolic shape as discussed by Zverev et al. (2017) and Celestre et al. (2020).
The minimum beam diameter of 700 nm was measured at distance Z = 0 mm (see Fig. 5). This value is significantly larger than the theoretical value. As discussed in the previous section, we assume that the main reason for that discrepancy is the influence of the secondary electron cascade. To estimate the real beam diameter in the focal plane, we compared a Gaussian profile which fits the shape of experimental caustics in its wings observed out of the focal region (Fig. 6). The analysis of the caustics was done using equation (1). In Fig. 6 the dependence of the beam radius rz, measured in the LiF images (Fig. 5), at position Z along the X-ray propagation axis is shown by black squares. In calculations, r0 and the beam quality factor M2 were varied. Considering the smallest beam size measured on the LiF image, a caustic of the Gaussian beam was calculated for parameters r0 = 0.35 µm and M2 = 1. As can be seen in Fig. 6, in this case, the corresponding curve (in blue) lies completely out of experimental data, with the exception of the area ±2 mm from the focal point. However, by taking into account the error bars, the beam size in the focal plane can correspond to a value of 2r0 = 0.1 µm. We calculated the beam divergence on the assumption that the focal beam radius r0 was in the range 0.05–0.35 µm and the beam quality factor M2 = 1–4. We found that the best fit of the experimental results takes place in the case of 2r0 = 0.41 µm and M2 = 3 (green solid line). Thus, we may assume that the real focal beam diameter at the FWHM signal level is about 0.41 µm.
The value of the focal spot determined in our experiment exceeds almost twice the value of ∼200 nm that the CRL4 unit is expected to satisfy according to the technical specifications. On the one hand, this may be due to the fact that the spatial resolution of the LiF is not sufficient to accurately determine the size of the beam in the focal plane; however, the beam caustics at distant points in Fig. 6 show that the size was still larger than 200 nm. Thus, the larger beam size is most likely related to lens aberrations and beam clipping. To test how lensing errors can affect the intensity distribution within a focused beam, we simulated the propagation of X-rays through the CRL4 stack as part of our study.
All simulations were made using the browser-based GUI framework Sirepo by RadiaSoft (Rakitin et al., 2018). It allows running beamline simulations on a personal computer via Synchrotron Radiation Workshop (SRW) code (Chubar & Elleaume, 1998). The capabilities of the SRW code for X-ray lens modeling have been presented, for example, by Celestre et al. (2020).
Schematically the optical elements used in the simulated beamline and watchpoints of the simulated images are shown in the upper part in Figs. 7 and 8. In our simulation, the Gaussian X-ray beam with a photon energy of 9 keV passes through the Be lens stack (refractive index decrement 4.20757 × 10−6, attenuation length 7.31 mm) which corresponds to the CRL4 unit used in our experiment with the following parameters: number of lenses N = 20, radius of parabolic curvature R = 50 µm, web thickness D = 30 µm, and aperture size = 316 µm (see Table 1). For this case, the focal length of the lens stack is 303 mm and the diffraction-limited spot size is ∼200 nm. The beam intensity distribution was obtained in the distance range ±24 mm from the focal plane.
To reproduce manufacturing errors in the CRL4 stack and estimate a shape and phase imperfection, a thin beryllium slice (used as phase distorter) was placed directly behind the lens casing along the optical path in the simulated beamline. We consider commonly encountered fabrication errors in the optical imperfections in refractive lenses such as deviation of shape from parabolic as well as error in the wall thickness at the tip of the parabola. The thickness profile of the phase distorter from beryllium was set as the Gaussian shape distribution. This simple model allows the deviation of the lens from the ideal parabolic surface to be taken into account. We were able to simulate the effects of figure errors on beam shape and intensity along the optical axis. The width (FWHM) of the phase distorter determined the deviation of the shape lenses from the ideal parabolic, and the thickness (D) specified the total error in the wall thickness at the tip of the parabola along the beam propagation path.
At first, the SRW simulations were performed for X-ray beam propagation through an ideal CRL4 stack (without phase distorter). The image series `Perfect CRL' for this case is shown in Fig. 7. As can be seen, the modeled images differ from the experimental ones, in which aberration is observed. This is due to the imperfection of the parabolic shape for the refracting surface of CRL4. As the next step, a phase distorter after the CRL4 stack was used in the simulation. At first, the FWHM of the phase distorter only was varied from 10 µm up to the radius of curvature of the CRL4 lens, 50 µm. As seen from Fig. 7, the best fit is observed for the FWHM of 30 µm.
Fig. 8 shows the simulation results for when varying the thickness D of the phase distorter in the range 5–20 µm. Experimentally recorded images of shaped beams are in good agreement with computer calculations. Performed simulations for the phase distorter with parameters FWHM = 30 µm and D = 10 µm are in good agreement with experimental data. However, it is clearly seen that the experimentally observed beam distribution is far from the expected one for perfect CRL4. The value D = 10 µm corresponds to an imperfection in the total wall thickness in the CRL stack of less than 1%. These results confirm that the output intensity distribution of the focused beam is extremely sensitive to the quality of the manufacturing and precision of assembling the CRL elements.
4. Conclusion
The capabilities of compound refractive focusing systems available at the HED instrument of the European XFEL facility were studied by direct imaging methods applying LiF fluorescent detection. Initial impressions of the focusing capabilities and qualities of the CRL3 and CRL4 units were recorded in the interaction chamber 1. Focus profiles were interpolated to sub-micrometer precision based on recording of the transitional focus of the CRL along it focusing axis. The images also revealed a micrometer-precision intensity distribution of the X-ray profile, indicating various contributions from the beamline optics to the X-ray profiles. The X-ray sensitivity and
available with LiF crystals would benefit any SASE-based X-ray facility, especially for beamlines with scientific scopes that are greatly dependent on the X-ray pulse profile and focus qualities.Acknowledgements
The reported research was performed in 2020–2021. SRW calculations were carried out on the computational resources of the JSCC RAS. The authors are grateful to Dr Alexei Buzmakov for a helpful discussion in terms of SRW modelling. We greatly thank Alexander Pelka, Hauke Höppner, Carsten Baehtz, Cornelius Strohm, Christian David, Clemens Prescher, Seniutinas Gediminas, Patrik Vagovic, Sebastian Göde and Andreas Schropp for their valuable contribution and support during the experiment. The beam diagnostics group at European XFEL (X-ray Photon Diagnostics) provided the sample environment and optical setup including the area detector. The translation stages were provided by the High Energy Density Instrument group. The authors are indebted to the HIBEF user consortium for the provision of instrumentation and staff that enabled this experiment. We acknowledge European XFEL in Schenefeld, Germany, for provision of X-ray free-electron laser beam time at HED SASE2 and would like to thank the staff for their assistance. Data recorded for the experiment at the European XFEL are available at doi:10.22003/XFEL.EU-DATA-002575-00.
Funding information
The work was carried out with the financial support of the Russian Federation represented by the Ministry of Science and Higher Education of the Russian Federation (grant No. 075-15-2021-1352); Osaka University team acknowledges the support from JSPS KAKENHI (grant No. 21K03499); TB, VH, JC and VV appreciate a partial financial support provided by the Czech Science Foundation (grant No. 20-08452S).
References
Baldacchini, G., Bollanti, S., Bonfigli, F., Flora, F., Di Lazzaro, P., Lai, A., Marolo, T., Montereali, R. M., Murra, D., Faenov, A., Pikuz, T., Nichelatti, E., Tomassetti, G., Reale, A., Reale, L., Ritucci, A., Limongi, T., Palladino, L., Francucci, M., Martellucci, S. & Petrocelli, G. (2005). Rev. Sci. Instrum. 76, 113104. Web of Science CrossRef Google Scholar
Berujon, S., Ziegler, E. & Cloetens, P. (2015). J. Synchrotron Rad. 22, 886–894. Web of Science CrossRef IUCr Journals Google Scholar
Boesenberg, U., Samoylova, L., Roth, T., Zhu, D., Terentyev, S., Vannoni, M., Feng, Y., van Driel, T. B., Song, S., Blank, V., Sinn, H., Robert, A. & Madsen, A. (2017). Opt. Express, 25, 2852–2862. Web of Science CrossRef CAS PubMed Google Scholar
Bonfigli, F., Hartley, N. J., Inubushi, Y., Katagiri, K., Koenig, M., Matsuoka, T., Makarov, S., Montereali, R. M., Nichelatti, E., Ozaki, N., Piccinini, M., Pikuz, S., Pikuz, T., Sagae, D., Vincenti, M. A. & Yabuuchi, T. (2021). Nuovo Cim. Della Soc. Ital. Di Fis. C, 44, 146. Google Scholar
Celestre, R., Chubar, O., Roth, T., Sanchez del Rio, M. & Barrett, R. (2020). Proc. SPIE, 11493, 114930J. Google Scholar
Chalupský, J., Boháček, P., Burian, T., Hájková, V., Hau-Riege, S. P., Heimann, P. A., Juha, L., Messerschmidt, M., Moeller, S. P., Nagler, B., Rowen, M., Schlotter, W. F., Swiggers, M. L., Turner, J. J. & Krzywinski, J. (2015). Phys. Rev. Appl. 4, 014004. Google Scholar
Chalupsky, J., Bohacek, P., Hajkova, V., Hau-Riege, S. P., Heimann, P. A., Juha, L., Krzywinski, J., Messerschmidt, M., Moeller, S. P., Nagler, B., Rowen, M., Schlotter, W. F., Swiggers, M. L. & Turner, J. J. (2011). Nucl. Instrum. Methods Phys. Res. A, 631, 130–133. Web of Science CrossRef CAS Google Scholar
Chubar, O. & Elleaume, P. (1998). Proceedings of the Sixth European Particle Accelerator Conference (EPAC98), 22–26 June 1998, Stockholm, Sweden, pp. 1177–1179. Google Scholar
Daurer, B. J., Sala, S., Hantke, M. F., Reddy, H. K. N., Bielecki, J., Shen, Z., Nettelblad, C., Svenda, M., Ekeberg, T., Carini, G. A., Hart, P., Osipov, T., Aquila, A., Loh, N. D., Maia, F. R. N. C. & Thibault, P. (2021). Optica, 8, 551–562. Web of Science CrossRef Google Scholar
Grum-Grzhimailo, A. N., Pikuz, T., Faenov, A., Matsuoka, T., Ozaki, N., Albertazzi, B., Pikuz, S., Inubushi, Y., Yabashi, M., Tono, K., Yumoto, H., Ohashi, H., Ishikawa, T. & Kodama, R. (2017). Eur. Phys. J. D, 71, 69. Google Scholar
Hagemann, J., Vassholz, M., Hoeppe, H., Osterhoff, M., Rosselló, J. M., Mettin, R., Seiboth, F., Schropp, A., Möller, J., Hallmann, J., Kim, C., Scholz, M., Boesenberg, U., Schaffer, R., Zozulya, A., Lu, W., Shayduk, R., Madsen, A., Schroer, C. G. & Salditt, T. (2021). J. Synchrotron Rad. 28, 52–63. Web of Science CrossRef IUCr Journals Google Scholar
Keitel, B., Plönjes, E., Kreis, S., Kuhlmann, M., Tiedtke, K., Mey, T., Schäfer, B. & Mann, K. (2016). J. Synchrotron Rad. 23, 43–49. Web of Science CrossRef CAS IUCr Journals Google Scholar
Liu, Y., Seaberg, M., Zhu, D., Krzywinski, J., Seiboth, F., Hardin, C., Cocco, D., Aquila, A., Nagler, B., Lee, H. J., Boutet, S., Feng, Y., Ding, Y., Marcus, G. & Sakdinawat, A. (2018). Optica, 5, 967–975. Web of Science CrossRef CAS Google Scholar
Mabey, P., Albertazzi, B., Michel, T., Rigon, G., Makarov, S., Ozaki, N., Matsuoka, T., Pikuz, S., Pikuz, T. & Koenig, M. (2019). Rev. Sci. Instrum. 90, 063702. Web of Science CrossRef PubMed Google Scholar
Maeda, Y., Hironaka, Y., Iwasaki, T., Kawasaki, K., Sakawa, Y., Izumi, T., Ota, M., Egashira, S., Nakagawa, Y., Higashi, N., Sentoku, Y., Kodama, R., Ozaki, N., Matsuoka, T., Somekawa, T., Yabuuchi, T., Inubushi, Y., Togashi, T., Kon, A., Sueda, K., Miyanishi, K., Shingubara, S., Shimizu, T., Okumura, A. & Shigemori, K. (2020). High Energy Density Phys., 36, 100813. Web of Science CrossRef Google Scholar
Makarov, S., Pikuz, S., Ryazantsev, S., Pikuz, T., Buzmakov, A., Rose, M., Lazarev, S., Senkbeil, T., von Gundlach, A., Stuhr, S., Rumancev, C., Dzhigaev, D., Skopintsev, P., Zaluzhnyy, I., Viefhaus, J., Rosenhahn, A., Kodama, R. & Vartanyants, I. A. (2020). J. Synchrotron Rad. 27, 625–632. Web of Science CrossRef CAS IUCr Journals Google Scholar
Makita, M., Seniutinas, G., Seaberg, M. H., Lee, H. J., Galtier, E. C., Liang, M., Aquila, A., Boutet, S., Hashim, A., Hunter, M. S., van Driel, T., Zastrau, U., David, C. & Nagler, B. (2020). Optica, 7, 404–409. Web of Science CrossRef CAS Google Scholar
Pikuz, T., Faenov, A., Matsuoka, T., Matsuyama, S., Yamauchi, K., Ozaki, N., Albertazzi, B., Inubushi, Y., Yabashi, M., Tono, K., Sato, Y., Yumoto, H., Ohashi, H., Pikuz, S., Grum-Grzhimailo, A. N., Nishikino, M., Kawachi, T., Ishikawa, T. & Kodama, R. (2015). Sci. Rep. 5, 17713. Web of Science CrossRef PubMed Google Scholar
Pikuz, T., Faenov, A., Ozaki, N., Matsuoka, T., Albertazzi, B., Hartley, N. J., Miyanishi, K., Katagiri, K., Matsuyama, S., Yamauchi, K., Habara, H., Inubushi, Y., Togashi, T., Yumoto, H., Ohashi, H., Tange, Y., Yabuuchi, T., Yabashi, M., Grum-Grzhimailo, A. N., Casner, A., Skobelev, I., Makarov, S., Pikuz, S., Rigon, G., Koenig, M., Tanaka, K. A., Ishikawa, T. & Kodama, R. (2018). Matter Radiat. Extremes, 3, 197–206. Web of Science CrossRef Google Scholar
Rakitin, M. S., Moeller, P., Nagler, R., Nash, B., Bruhwiler, D. L., Smalyuk, D., Zhernenkov, M. & Chubar, O. (2018). J. Synchrotron Rad. 25, 1877–1892. Web of Science CrossRef IUCr Journals Google Scholar
Ruiz-Lopez, M., Faenov, A., Pikuz, T., Ozaki, N., Mitrofanov, A., Albertazzi, B., Hartley, N., Matsuoka, T., Ochante, R., Tange, Y., Yabuuchi, T., Habara, T., Tanaka, K. A., Inubushi, Y., Yabashi, M., Nishikino, M., Kawachi, T., Pikuz, S., Ishikawa, T., Kodama, R. & Bleiner, D. (2017). J. Synchrotron Rad. 24, 196–204. Web of Science CrossRef CAS IUCr Journals Google Scholar
Rutishauser, S., Samoylova, L., Krzywinski, J., Bunk, O., Grünert, J., Sinn, H., Cammarata, M., Fritz, D. M. & David, C. (2012). Nat. Commun. 3, 947. Web of Science CrossRef PubMed Google Scholar
Schneider, M., Günther, C. M., Pfau, B., Capotondi, F., Manfredda, M., Zangrando, M., Mahne, N., Raimondi, L., Pedersoli, E., Naumenko, D. & Eisebitt, S. (2018). Nat. Commun. 9, 214. Web of Science CrossRef PubMed Google Scholar
Schneidmiller, E. & Yurkov, M. (2011). Technical Report DESY 11–152. Deutsches Elektronen-Synchrotron, Hamburg, Germany. Google Scholar
Schropp, A., Hoppe, R., Meier, V., Patommel, J., Seiboth, F., Lee, H. J., Nagler, B., Galtier, E. C., Arnold, B., Zastrau, U., Hastings, J. B., Nilsson, D., Uhlén, F., Vogt, U., Hertz, H. M. & Schroer, C. G. (2013). Sci. Rep. 3, 1633. Web of Science CrossRef PubMed Google Scholar
Schropp, A., Hoppe, R., Meier, V., Patommel, J., Seiboth, F., Ping, Y., Hicks, D. G., Beckwith, M. A., Collins, G. W., Higginbotham, A., Wark, J. S., Lee, H. J., Nagler, B., Galtier, E. C., Arnold, B., Zastrau, U., Hastings, J. B. & Schroer, C. G. (2015). Sci. Rep. 5, 11089. Web of Science CrossRef PubMed Google Scholar
Seiboth, F., Fletcher, L. B., McGonegle, D., Anzellini, S., Dresselhaus-Cooper, L. E., Frost, M., Galtier, E., Goede, S., Harmand, M., Lee, H. J., Levitan, A. L., Miyanishi, K., Nagler, B., Nam, I., Ozaki, N., Rödel, M., Schropp, A., Spindloe, C., Sun, P., Wark, J. S., Hastings, J., Glenzer, S. H. & McBride, E. E. (2018). Appl. Phys. Lett. 112, 221907. Web of Science CrossRef Google Scholar
Seiboth, F., Schropp, A., Scholz, M., Wittwer, F., Rödel, C., Wünsche, M., Ullsperger, T., Nolte, S., Rahomäki, J., Parfeniukas, K., Giakoumidis, S., Vogt, U., Wagner, U., Rau, C., Boesenberg, U., Garrevoet, J., Falkenberg, G., Galtier, E. C., Ja Lee, H., Nagler, B. & Schroer, C. G. (2017). Nat. Commun. 8, 14623. Web of Science CrossRef PubMed Google Scholar
Self, S. A. (1983). Appl. Opt. 22, 658–661. CrossRef PubMed CAS Web of Science Google Scholar
Vartanyants, I. A., Singer, A., Mancuso, A. P., Yefanov, O. M., Sakdinawat, A., Liu, Y., Bang, E., Williams, G. J., Cadenazzi, G., Abbey, B., Sinn, H., Attwood, D., Nugent, K. A., Weckert, E., Wang, T., Zhu, D., Wu, B., Graves, C., Scherz, A., Turner, J. J., Schlotter, W. F., Messerschmidt, M., Lüning, J., Acremann, Y., Heimann, P., Mancini, D. C., Joshi, V., Krzywinski, J., Soufli, R., Fernandez-Perea, M., Hau-Riege, S., Peele, A. G., Feng, Y., Krupin, O., Moeller, S. & Wurth, W. (2011). Phys. Rev. Lett. 107, 144801. Web of Science CrossRef PubMed Google Scholar
Yumoto, H., Mimura, H., Koyama, T., Matsuyama, S., Tono, K., Togashi, T., Inubushi, Y., Sato, T., Tanaka, T., Kimura, T., Yokoyama, H., Kim, J., Sano, Y., Hachisu, Y., Yabashi, M., Ohashi, H., Ohmori, H., Ishikawa, T. & Yamauchi, K. (2013). Nat. Photon. 7, 43–47. Web of Science CrossRef CAS Google Scholar
Zastrau, U., Appel, K., Baehtz, C., Baehr, O., Batchelor, L., Berghäuser, A., Banjafar, M., Brambrink, E., Cerantola, V., Cowan, T. E., Damker, H., Dietrich, S., Di Dio Cafiso, S., Dreyer, J., Engel, H.-O., Feldmann, T., Findeisen, S., Foese, M., Fulla-Marsa, D., Göde, S., Hassan, M., Hauser, J., Herrmannsdörfer, T., Höppner, H., Kaa, J., Kaever, P., Knöfel, K., Konôpková, Z., Laso García, A., Liermann, H.-P., Mainberger, J., Makita, M., Martens, E.-C., McBride, E. E., Möller, D., Nakatsutsumi, M., Pelka, A., Plueckthun, C., Prescher, C., Preston, T. R., Röper, M., Schmidt, A., Seidel, W., Schwinkendorf, J.-P., Schoelmerich, M. O., Schramm, U., Schropp, A., Strohm, C., Sukharnikov, K., Talkovski, P., Thorpe, I., Toncian, M., Toncian, T., Wollenweber, L., Yamamoto, Sh. & Tschentscher, T. (2021). J. Synchrotron Rad. 28, 1393–1416. Web of Science CrossRef CAS IUCr Journals Google Scholar
Zverev, D., Barannikov, A., Snigireva, I. & Snigirev, A. (2017). Opt. Express, 25, 28469. Web of Science CrossRef Google Scholar
This is an open-access article distributed under the terms of the Creative Commons Attribution (CC-BY) Licence, which permits unrestricted use, distribution, and reproduction in any medium, provided the original authors and source are cited.