![](/logos/buttonlogos/cross.png)
![](/logos/buttonlogos/cross.png)
research papers
PEPICO analysis of catalytic reactor effluents towards quantitative isomer discrimination: DME conversion over a ZSM-5 zeolite
aNano and Molecular Systems Research Unit, University of Oulu, Oulu, Finland, bDepartment of Chemistry, Centre for Materials Science and Nanotechnology (SMN), University of Oslo, Oslo, Norway, and cMAX IV Laboratory, Lund University, Lund, Sweden
*Correspondence e-mail: morsal.babayan@oulu.fi, evgeniy.redekop@smn.uio.no, samuli.urpelainen@oulu.fi
The methanol-to-hydrocarbons (MTH) process involves the conversion of methanol, a C1 feedstock that can be produced from green sources, into hydrocarbons using shape-selective microporous acidic catalysts – zeolite and zeotypes. This reaction yields a complex mixture of species, some of which are highly reactive and/or present in several isomeric forms, posing significant challenges for effluent analysis. Conventional gas-phase
(GC) is typically employed for the analysis of reaction products in laboratory flow reactors. However, GC is not suitable for the detection of highly reactive intermediates such as ketene or formaldehyde and is not suitable for kinetic studies under well defined low pressure conditions. Photoelectron–photoion coincidence (PEPICO) spectroscopy has emerged as a powerful analytical tool for unraveling complex compositions of catalytic effluents, but its availability is limited to a handful of facilities worldwide. Herein, PEPICO analysis of catalytic reactor effluents has been implemented at the FinEstBeAMS beamline of MAX IV Laboratory. The conversion of dimethyl ether (DME) on a zeolite catalyst (ZSM-5-MFI27) is used as a prototypical model reaction producing a wide distribution of hydrocarbon products. Since in zeolites methanol is quickly equilibrated with DME, this reaction can be used to probe vast sub-networks of the full MTH process, while eliminating or at least slowing down methanol-induced secondary reactions and Quantitative discrimination of xylene isomers in the effluent stream is achieved by deconvoluting the coincidence photoelectron spectra.Keywords: PEPICO; zeolite catalyst; isomer selectivity; dimethyl ether to hydrocarbons conversion; reactor effluent analysis; synchrotron radiation; electron spectroscopy; ion mass spectrometry.
1. Introduction
Catalytic transformations of hydrocarbons and other organic molecules inside microporous acidic zeolites drive many large-scale industrial chemical processes with enormous combined economic and environmental impact (Cejka et al., 2010). Some zeolite-mediated catalytic processes are also key candidates for implementing more sustainable transformations of diversified raw materials and renewable energy into vital energy carriers and chemical intermediates (Li & Yu, 2021
). Highly convoluted reaction networks and microporous transport phenomena involved in catalysis by zeolites often present formidable experimental challenges. Complex effluent streams produced by zeolite catalysts may contain dozens of compounds, many of them present in several isomeric forms. (GC) is a commonly used technique for effluent analysis in laboratory experiments that are typically conducted at ambient or above-ambient pressure conditions. However, GC is limited to the analysis of gas samples extracted from ambient or near-ambient pressure conditions and is not suitable for capturing highly reactive closed and open shell gaseous intermediates, e.g. formaldehyde, or radicals. Kinetic measurements under well defined, low pressure reaction conditions have emerged as an important source of mechanistic information because these highly reactive intermediates can be more readily detected and quantified by (Brogaard et al., 2014
; Batchu et al., 2017
; Omojola et al., 2021
). Likewise, low pressure operation prolongs the catalyst lifetime by minimizing secondary reactions and coking, thus expanding the range of catalyst states that are amenable for precise kinetic characterization (Redekop et al., 2020
). Isomer-selective analytics at low-pressure conditions would open new avenues for advanced kinetic characterization of catalytic reactions at model operating conditions that facilitate in-depth mechanistic studies.
Photoionization et al., 2020). Although the electron and ion spectroscopy methods alone play a major part in studying molecular photofragmentation, in particular, recording and analyzing electrons and ions originating from the same event can lead to a more complete understanding of the photofragmentation process and the composition of the effluent gas stream. Taking the type of detected particles into account, coincidence techniques may be classified as photoelectron–photoion coincidence (PEPICO), photoion–photoion coincidence (PIPICO), photoelectron–photoion–photoion coincidence (PEPIPICO), photoelectron–photoelectron coincidence and photoion–neutral coincidence (Arion & Hergenhahn, 2015
). PEPICO and threshold PIMS have been most instrumental in unraveling the reaction mechanisms of methanol-to-hydrocarbons (MTH), catalytic and oxychlorination processes (Hemberger et al., 2020
). With the aid of in situ synchrotron radiation PIMS, Wen et al. (2020
) have detected formaldehyde (HCHO), an active intermediate, during the MTH reaction over two catalysts. Recently, Cesarini et al. (2022
) utilized operando PEPICO spectroscopy to investigate reaction pathways for MTH and MCTH (methyl chloride-to-hydrocarbons) over the H-ZSM-5 zeolite catalyst. Using this technique they directly observed short-lived active intermediates, such as ketene and methyl radicals. Despite the increasing interest in applying these methods to investigate catalytic reactions, few experimental setups exist which combine catalytic microreactors with PIMS-based effluent analysis.
Herein, we report the establishment of such an instrument at the gas-phase endstation of the FinEstBeAMS beamline of MAX IV Laboratory (Lund, Sweden). Currently there are only a handful of synchrotron beamlines providing capabilities for the PIMS-based analysis of catalytic reactor effluents, including FinEstBeAMS. Features of some of them are are compared in Table 1. The main differences between these setups are the accessible energy ranges and the types of available detectors. The VUV beamline at the Swiss Light Source (SLS) offers photons in the 3–150 eV range and is capable of both photoion and photoelectron analysis (SLS, 2023
). The BL03U beamline at the National Synchrotron Radiation Laboratory (NSRL) in China has a relatively narrow photon energy range of 5–21 eV and only detects ions (Zhou et al., 2016
). The DESIRS beamline at Synchrotron SOLEIL, France, covering the VUV range (5–40 eV) is equipped with a double imaging photoelectron photoion coincidence (i2PEPICO) spectrometer with two position-sensitive detectors to detect both photoelectrons and photoions (Tang et al., 2015
). In comparison, FinEstBeMS covers a broad range of photon energies, 4.4–1000 eV, which enables both valence and core ionization, and features ion and electron analysis as well as coincidence experiments.
‡Differentially pumped molecular beam extraction for experiments up to 103 mbar is under design/construction at the University of Oulu. |
The conversion of methanol and/or dimethyl ether (DME) to hydrocarbons, abbreviated as MTH and DTH, respectively, on acidic zeolites and zeotypes offers a prototypical example of a catalytic reaction which produces compositionally and isomerically complex effluents (Olsbye et al., 2012). MTH/DTH are promising industrial routes towards hydrocarbon fuels and platform chemicals, which can accommodate diverse feedstocks including bio-gas and captured CO2 (Xie & Olsbye, 2023
). In acidic zeolite or zeotype catalysts, an equilibrated mixture of DME and methanol react on Brønsted acid sites (BAS) to produce larger hydrocarbon molecules including and aromatics. The reaction proceeds through the dual-cycle hydrocarbon pool (HCP) mechanism in which several pathways can be distinguished. The first C—C bonds are formed from DME and/or methanol via surface methoxy species (SMS) and highly reactive intermediates such as formaldehyde or ketene, eventually leading to C2–C3 These primary products are then repeatedly methylated by SMS (stepwise pathway) or gaseous DME/methanol to form C3–C5+ – the so-called alkene cycle. The product distribution is further controlled by co-occurring cracking reactions. Hydrogen transfer reactions between methanol and also catalyzed by BAS, lead to the formation of and aromatics. The latter can sustain an independent cycle of sequential methylation and cracking – the aromatics cycle. At the population of in situ generated alkene and aromatics intermediates termed the HCP resides within the catalyst and mediates continuous catalytic production of products from DME/methanol, in parallel with the hydrogen transfer and isomerization reactions. Moreover, methyl radicals were also detected in the reaction medium, suggesting that the underlying chemistry may be even more complex than previously thought. Eventually, the growth of large polyaromatic molecules and coke occludes the microporous space and deactivates the catalyst.
Catalytic performance, i.e. activity, selectivity and stability, is ultimately controlled by a multitude of factors related to the catalyst structure and operating conditions. In order to establish the structure–performance relationships and optimize the catalytic materials and reactions, it is imperative to better understand the kinetics of different reaction pathways and how they are affected by variations of the materials composition and structure. However, disentangling the distinct reaction pathways and individual reaction steps is a challenging experimental task, given the aforementioned complexity. PIMS-based methodologies for the reaction analysis have already provided essential mechanistic insights into methanol-to-olefins (MTO) chemistry, and this provides the main motivation for the current study – to showcase the new operando PEPICO capabilities at the FinEstBeAMS beamline in the context of this important reaction. In particular, we demonstrate PEPICO analysis of DME conversion on a ZSM-5 catalyst with a particular emphasis on quantitative isomer discrimination for the product xylenes.
2. Experiments
In this study, the products of the DME reaction over the ZSM-5 zeolite catalyst at a temperature of 375°C are investigated in real time, during the catalytic process, through operando PEPICO spectroscopy. This investigation has been performed using a coincidence setup at the gas-phase endstation (GPES) of the FinEstBeAMS beamline at the MAX IV Laboratory. Pure DME was fed into the reactor at a rate of 0.045 s.c.c.m. (standard cubic centimeters per minute) via a precision leak valve opening directly into the packed bed. At this feed rate, the pressure in the analysis chamber remained at 5 × 10−7 mbar. In this experiment, photons with an energy of 40 eV were utilized as the ionization source. The electron analyzer operates at a pass energy of 100 eV with the window centered at 28 eV. Hence, electrons with kinetic energies within the range 23–33 eV (equivalent to binding energies of 7–17 eV) were captured. Moreover, the measurement was conducted at the magic angle of 55°. While the beamline has a sub-meV resolution at 40 eV photon energy (Pärna et al., 2017), the electron spectrometer resolution was approximately 600 meV. The electron count rate and random trigger frequency were kept at about 25 Hz to have a better coincidence purity. In total, over a duration of approximately 15 h, nearly 2 × 106 triggers were detected, in which roughly 21% of them were coincidence triggers. Coincidence-specific data handling was performed with custom Igor Pro macros (Kukk et al., 2007
).
2.1. Gas-phase endstation
The FinEstBeAMS beamline is in the 1.5 GeV storage ring providing photon energy in the range from ultraviolet to soft X-ray (i.e. 4.5 to 1300 eV) as well as variable polarization of synchrotron radiation. Detailed information on the design and optical concept of the FinEstBeAMS beamline is given elsewhere (Pärna et al., 2017; Chernenko et al., 2021
). The FinEstBeAMS beamline consists of two separate branch lines. The GPES and the endstation (PLES) are in the same branch, while the solid-state endstation (SSES) is located in the other one.
The GPES was developed for electron and ion spectroscopy as well as photoelectron–photoion coincidence spectroscopy of low-density matter. Kooser et al. (2020) describe the GPES in more details. Briefly, in this apparatus a modified hemispherical electron energy analyzer (SCIENTA R4000) equipped with a fast resistive anode position-sensitive detector is utilized to detect photoelectrons. Moreover, a Wiley–McLaren ion time-of-flight (TOF) with delay-line position-sensitive detector detects ions produced throughout the ionization. In order to calibrate the TOF spectrum to masses, the following formula is utilized: m/z = (TOF − T0)2/C2. Here, the calibration parameters are determined by using the peaks corresponding to masses 2 (H2) and 91 (C7H7) as the initial guess. Using these initial values, we calculate T0 = 1715 ns and C = −11.59 ns (e/a.m.u.)1/2 (in which e and a.m.u. are the and units, respectively) which ensures that all other TOF peaks fall into the correct masses.
2.2. Reactor
A portable, flange-mounted catalytic packed-bed reactor (length 50 mm, internal diameter 4 mm) was interfaced directly with the GPES endstation, as shown in Fig. 1. In brief, 20 mg of a catalytic sample was packed in the middle of the reactor as a thin (2 mm) layer sandwiched between two inert zones that were packed with quartz particles of the same sieve fraction. The reactor was resistively heated, while the temperature was monitored by a K-type thermocouple positioned in the middle of the catalytic bed. Gaseous reactants were fed into the reactor through a calibrated leak valve, and the effluent was allowed to freely enter the analysis chamber where the gas was pumped away by three turbomolecular pumps with total capacity of about 1300 l s−1. A schematic of the reactor connected to the GPES is presented in Fig. 1
.
![]() | Figure 1 Schematic of the reactor connected to the gas-phase endstation at the FinEstBeAMS beamline of MAX IV Laboratory. |
2.3. Materials and reagents
A commercial ZSM-5-MFI-27 zeolite was purchased from Sud Chemie. To obtain the acidic form of the catalyst, the as-received material was ion-exchanged with NH4NO3, extensively washed, and calcined in static air at 550°C for 10 h. Then, the catalyst was pressed into pellets that were sieved to 250 < dp < 400 µm size fraction, which were subsequently packed into the reactor. Before the experiment, the catalyst was maintained in vacuum at 550°C for 30 min to desorb the residual water. A detailed procedure for the catalyst preparation and extensive standard characterization data has been given by Rojo-Gama et al. (2018).
Basic physico-chemical properties were determined to be as follows: Si/Al ratio of 15, BAS (Brønsted acid sites) concentration of 0.87 mmol g−1, crystal size of 2–6 µm, and BET (Brunauer–Emmett–Teller) surface area of 398 m2 g−1.
2.4. PEPICO
In this study, operando PEPICO spectroscopy is used, which, aside from being isomer-selective, is able to qualitatively differentiate short- and long-lived species as well.
In PEPICO spectroscopy, both the photoelectron and the photoion generated via the ionization are detected. For regular PEPICO spectroscopy, the et al., 2013). To detect different isomers using threshold-PEPICO, tunable light sources with sufficiently high resolution are required. Hence, the regular PEPICO technique (from hereon PEPICO), readily available at FinEstBeAMS, is considered in this study.
The products of the reaction and the remaining reactant (when the conversion rate is less than 100%) leaving the microreactor are ionized by the photon beam. This leads to the generation of ions and electrons in the extraction region of the TOF
When an electron is detected by the electron analyzer, a signal is generated to initiate a pulsed electric field in the extraction region of the mass spectrometer.Since the electron mass is negligible compared with the ions, the flight times of electrons are significantly lower than for the ions, therefore it is reasonable to assume that the formation of the ions and the detection of the electron occur concomitantly. Eventually, the electron–ion pairs associated with the same
event can be distinguished by correlating the detected electrons and ions.2.4.1. True/false coincidences
Although one electron is detected each time, ionizing more than one atom or molecule throughout the ionization process is possible which leads to the detection of electron–ion pairs that are not coming from the same event. Such events are known as false coincidences. By applying a low ionization rate, the probability of detecting the electron–ion pairs arising from the same event (true coincidences) increases, as the generated electron–ion pairs will be well separated in time (Bodi et al., 2013). Furthermore, less than a 100% of the electron and ion detectors (which is lower for the electron) contributes to the false coincidences. To distinguish the ions generated by true coincidences, subtracting the random ions coming from the false coincidences is required. Consequently, a reference random coincidence must be measured under exactly the same conditions. Hence, an external pulse generator is used to create artificial random triggers besides electron triggers. For those random triggers, all measured coincidences would be false coincidences. Eventually, subtracting the random coincidences from total coincidences coming from electron triggers leads to true coincidences. Previously (Prümper & Ueda, 2007
), coincidence experiments and the random coincidences subtraction method have been described in more detail. Here, random triggers generated by an external pulse generator with 25 Hz frequency is utilized. The TOF spectra from electron-triggered, random and true coincidences are depicted in Fig. S1 of the supporting information.
2.4.2. Electron spectra
PEPICO measurements provide both the TOF of ions, revealing the mass per charge ratio of the ions, as well as the et al. (2022), can be used to provide additional information. For atoms, shows the binding energies of the electrons, whereas, for molecules, it reveals vibrational and rotational excitations as well.
Photoelectron spectroscopy reveals key features of the original molecular orbitals from which the electrons are emitted. On the other hand, isomers of a molecule have distinct electronic structures due to differences in the relative positioning of substituent groups, such as methyl groups in xylene, which can alter electronic density and molecular symmetry. This makes m- and p-xylene by Koenig et al. (1974) using He(I) radiation revealed that the first ionic states of these isomers have distinct potentials that can be utilized for differentiation purposes. Likewise, unique features observed in the photoelectron spectra of cis-, trans- and iso-butene can serve as distinctive markers to differentiate between these isomers (Ying et al., 1993
). Therefore, utilizing CIY-PES can be a valuable tool for differentiating between ions with identical mass/fragments.
3. Results and discussion
3.1. TOF spectra
The detected ions, representing the effluent stream during the conversion of DME on the ZSM-5 catalyst, are generated mainly by single valence ionization, as the
for direct double is low. Therefore, for the sake of abbreviation, instead of mass per charge ratio, only mass is going to be used.A broad range of ions, covering masses from 1 to 156, are detected in the effluent stream. Table 2 lists the masses detected in true coincidences and the possible corresponding molecular ions. The calibrated TOF spectrum of true ions detected in coincidence with electrons in the binding energy range of approximately 8 to 17 eV is depicted in Fig. 2
(b). Due to the negligible intensity observed for ions with masses greater than 120, they are excluded from the figure. Furthermore, it is noteworthy to highlight that the comparison between the TOF spectrum for DME flowing over the blank reactor closely resembles the reference spectrum provided in the NIST Chemistry WebBook (Wallace, 2018
). This correspondence effectively mitigates concerns regarding the potential reactivity of DME (on the walls of the reactor and/or inert packing) under these experimental conditions. The TOF spectra of a mixture of Ar and DME (3:1 ratio) flowing over the empty reactor is plotted in Fig. S2 for two different rector temperatures.
|
![]() | Figure 2 (a) PEPICO map of the effluent stream of DME conversion over ZSM-5 zeolite at 375°C ionized using light with 40 eV energy, (b) integrated binding energy spectrum and (c) integrated ion TOF spectrum with false coincidences subtracted. For higher TOF, the spectrum intensity is multiplied by 15 to make it more clear. The corresponding mass per charge ratios are mentioned for groups of TOF peaks. |
In the current experiment, DME is not present in the effluent and its complete conversion is attained under the considered conditions. Feng et al. (2001) reported that, at 40 eV photon energy for DME, the branching ratios of ions with masses 46 and 45 were about 13.6% and 22.5%, respectively. However, ions with these masses are not detected in this study (as shown in Table 2
).
In Fig. 2(b), the peak with the highest intensity corresponds to H2O+ (mass 18) – an expected result, considering that water is a major product of DME conversion on zeolite catalysts (Chang, 1983
). The peak with the second highest intensity corresponds to the mass 28, which can be attributed to N2+, CO+ and/or C2H4+ cations. However, it is not possible to determine from the TOF spectrum alone whether all of these cations contribute to this peak or not. Moreover, the peaks for masses 16 and 15 exhibit noticeable intensities in the recorded spectrum. The CH3+ cation is the only plausible candidate for the peak with mass 15, given that the effluent is expected to contain hydrocarbons, water and residual oxygenates (DME and methanol). However, it is possible that both CH4+ and O+ contribute to the peak observed at the mass 16. Based on the peaks observed at masses 18, 28, 32 and 44, it is possible that the O+ cation detected in the experiment originates from the fragmentation of H2O, CO, O2, CH3OH or CO2 molecules, respectively. Nonetheless, the absence of a peak at mass 31 implies that CH3OH is not present in the effluent stream, which is consistent with a complete conversion of oxygenates on ZSM-5 catalyst at these conditions. For the peak at mass 44, both CO2+ and C3H8+ are the possible cations that we cannot discriminate only by TOF measurement. There is a group of small peaks at masses 39–42, which originate possibly from photofragmentation of propylene.
The TOF spectra show a pair of peaks at masses 91 and 92, which correspond to C7H7+ and C7H8+, respectively, and are the major fragments of toluene. Moreover, apart from C8H9+ and C8H10+, C7H7+ is a main fragment of xylene. The pair of peaks observed at 105 and 106 represent C8H9+ and C8H10+ cations, respectively. Although the TOF spectrum provides valuable information about the potential parent molecules in the effluent stream, toluene and xylene in this case, it is not possible to determine the specific origin of the C7H7+ cation.
In general, conventional
techniques, including TOF, have limitations when it comes to analyzing the complex mixtures or molecules with identical masses (like isomers) or those exhibiting similar fragments. Hence, alternative techniques like PEPICO are employed to overcome these limitations and provide more detailed information about the parent molecules. This is achieved by recording the of the detected electrons and extracting CIY-PES for each detected masses. These spectra can then be compared with the previously reported spectra of potential parent molecules to validate the identification achieved by mass spectrometry.3.2. PEPICO
Fig. 2 shows an electron-energy-resolved PEPICO map of electronic states with binding energies between 8 and 17 eV. This figure shows a map of the event intensities for all ion TOF and electron energy pairs. The horizontal axis corresponds to the electron hit position energies (which is calibrated to the electron binding energy in the top panel) and the vertical axis corresponds to the simultaneously detected ion flight times. This map provides an overview of the fragmentation patterns by associating specific electron binding energies with their corresponding positively charged fragments. False coincidences have been removed and slight smoothing is applied for better visualization. While the general trend can be seen in Fig. 2
, a more detailed analysis should be conducted using the CIY-PES, which is given in the next section.
3.3. CIY photoelectron spectra
As described in Section 3.1, the TOF spectrum furnishes valuable insights into the mass distribution of ions within the chamber, along with their relative abundances, aiding in compound identification to a certain extent. However, when it comes to molecules with identical masses or a mixture of samples exhibiting similar ionization fragmentation patterns, TOF is limited. For instance, the mass 91 ionization fragment is predominant in both xylene and toluene, making them indistinguishable in a mixture using only TOF. CIY-PES within the framework of PEPICO addresses such challenges by providing additional information about the emitted photoelectrons in coincidence with the mass of interest.
Fig. 2(a) illustrates the photoelectron spectrum (PES) of all detected electrons in coincidence with true ions. In this section, we aim to discriminate between the different species in the effluent stream by comparing the extracted CIY-PES with those previously reported for potential source compounds. To perform this comparative analysis, reference spectra are digitized using the WebPlotDigitizer online software (Rohatgi, 2022
).
The TOF spectrum reveals two intense peaks at masses 15 and 16 [Fig. 2(b)]. The peak at mass 15 corresponds only to the CH3+ cation, while that at mass 16 can be attributed to CH4+ and O+ cations. The potential parent molecules that contain oxygen and can give rise to the O+ ion in this study are O2, CO, CO2, water and DME. However, the mass spectra of these molecules, as reported in the NIST Chemistry WebBook (Wallace, 2018
), would exhibit a considerably smaller peak at mass 16. In our dataset, DME undergoes complete conversion, and the molecular ions of O2, CO and CO2 have even lower intensities than mass 16. Additionally, according to the NIST Chemistry WebBook, the mass 16 fragment of water is negligible. Therefore, it is assumed that CH4+ is the main cation contributing to the peak in question.
Fig. 3(a) shows a comparison between the CIY-PES for masses 15 and 16, and their sum with the reference PES of CH4. The CIY-PES of mass 16 only covers a portion of the reference spectrum, while the CIY-PES of mass 15 covers the remaining section. The sum of these two spectra results in a spectrum that closely resembles the reference spectrum of CH4 as reported by Kimura (1981
). The ionization of a molecule can occur from different sites, including the bonding and antibonding orbitals. For CH4, the main fragmentation channels are (Chang et al., 2017
)
Therefore, aggregating the CIY-PESs collected with PEPICO for the main fragments (in this case CH3+ and CH4+) can result in a spectrum that is more representative of the reference spectra (i.e. CH4 PES). This is because, in reference spectra, electrons from all ionization channels, including all originating from both inner valence ionization and outermost shell ionization, are considered, whereas, in CIY-PES, only electrons generated in a channel are taken into account.
![]() | Figure 3 Comparison of extracted coincidence ion yield photoelectron spectra (CIY-PES) at 40 eV photon energy with reference spectra for the most intense detected cations (Kimura, 1981 ![]() ![]() ![]() ![]() |
Mass 18 exhibits the most prominent peak in the TOF spectrum, with water being the most likely species of origin, as stated previously. To verify this, the extracted CIY-PES for mass 18 is compared with the He(I) photoelectron spectrum of water in Fig. 3(b) (Kimura, 1981
). Despite the differences in the photon energies and the resolution, this figure demonstrates a favorable agreement between the measured and the reference spectra.
Based on the nature of the experiment, the most likely cations with mass 28 are C2H4+ (a product of the reaction), CO+ (a chamber contaminant) and N2+ (an air leak). Comparison of the corresponding CIY-PES for mass 28 with the reference He(I) photoelectron spectra of N2, CO and C2H2 (Kimura, 1981) (see Fig. S4) reveals that N2 and CO are present in the effluent stream. However, the reference spectrum for C2H4 displays a broad peak at a binding energy of 14.66 eV which is not captured by only the CIY-PES for mass 28. According to previous studies (Wallace, 2018
; Stockbauer & Inghram, 1975
), in addition to the molecular ion C2H4+, pure C2H4 also fragments into C2H3+ and C2H2+ with masses 27 and 26, respectively. The combined CIY-PES for masses 26, 27 and 28, indeed, demonstrate a better agreement with the reference photoelectron spectrum of pure C2H4 because it includes all major fragmentation channels [as presented in Fig. 3
(c)].
The detection of N2 indicates the presence of air leakage into the chamber, which is also confirmed by the observation of O2 with a distinct peak at mass 32 in the TOF spectrum [Fig. 2(b)] and the corresponding comparison of CIY-PES with the reference photoelectron spectrum for O2 (Kimura, 1981
) (see Fig. S5).
Ions with masses of 41 and 42 are also detected, albeit with low intensity. These ions could correspond to propylene (C3H6), which is an expected product of DME conversion, and ketene (C2H2O), which is a highly reactive intermediate of the reaction. Due to moderate spectral resolution and low signal-to-noise ratio, it is not possible to distinguish them from the PES. However, it can be inferred that the signal corresponds to propylene, since ketene is so reactive that it is not expected to survive the transport through the second inert zone in the reactor. Furthermore, mass 14 is the predominant fragment of ketene (Wallace, 2018), which is not detected in our TOF spectrum [Fig. 2
(c)]. The comparison between extracted CIY-PES for mass 42 and reference spectra for C3H6 and ketene is depicted in Fig. 3
(d).
Ions with mass 44 likely originate from CO2 and propane C3H8, the latter being an expected minor product of DME conversion via hydrogen transfer reactions between propylene and methanol. However, CIY-PES of mass 44 (Fig. S6) reveals that C3H8 does not exist in the chamber and all ions with mass 44 are CO2+. We attribute the presence of CO2 to a combination of (i) the chamber background, (ii) the product of decarboxylation of MTH reaction intermediates on the zeolite (Huber & Plessow, 2023), as well as (iii) the product of oxidation of hydrocarbons by a minute amount of oxygen in the background (Fig. S5).
Ions with mass 56 can be assigned to butene – another expected product of the reaction formed by methylation of propylene. However, the production of butene was limited, leading to a low signal-to-noise ratio for CIY-PES of mass 56.
According to Cesarini et al. (2022), various isomers of C5H8 can undergo additional cyclization/dehydrogenation and methylation reactions, resulting in the formation of cyclopentadiene (C5H6; m/z = 66) and methyl cyclopentadiene (C6H8; m/z = 80), respectively. Furthermore, they have identified fulvene (C6H6; m/z = 78) formed through the dehydrogenation of methyl cyclopentadienes (C6H8). Fulvene is a precursor for the production of benzene, the first aromatic ring compound. Direct methylation of fulvene, as well as dehydrogenation-methylation of C6H8, leads to the production of methyl fulvene (C7H8; m/z = 92), which is the primary precursor to toluene. This process can continue to generate other alkylated benzenes, including various isomers of xylene and trimethylbenzene. In the current experiment, masses 78 and 92 are detected, while 66 and 80 are not observed [Fig. 2
(b)]. To determine the identities of the detected peaks, a comparison between the CIY-PES obtained for masses 78 and 92, together with the relevant reference spectra are presented in Figs. 3
(e) and 3
(f), respectively (Kimura, 1981
; Cesarini et al., 2022
). The results indicate that benzene and toluene are the parent molecules associated with the detected peaks. However, it was not possible to detect intermediates such as fulvene and methyl fulvene in our experiments. We hypothesize that this limitation could be attributed to the experimental configuration of the reactor used in this study, i.e. the second inert zone of the packed bed.
In the present study, two peaks at masses 105 (C8H9+) and 106 (C8H10+) are observed in the TOF spectrum as shown in Fig. 2(b). Considering the it is inferred that xylene (C8H10) is the appropriate parent molecule associated with these peaks. The CIY-PES for mass 106 and the aggregation of CIY-PES for xylenes' main fragments (i.e. masses 106, 105 and 91) are compared with reference spectra in Fig. 3
(g). The CIY-PES for mass 106 does not fully coincide with the reference spectra of xylenes (Koenig et al., 1974
; Salaneck, 1981
) (see Fig. S7). However, the aggregation of CIY-PES for masses 106, 105 and 91, presenting electrons coming from three various ionization channels, more closely matches the reference spectra. This aligns with the practice in reference spectra where electrons from all ionization channels (including both inner valence ionization and outermost shell ionization) are accounted for. Conversely, in CIY-PES for mass 106, only electrons produced in the ionization channel of
are taken into consideration. The reference spectra of the xylenes shown in Fig. 3
(g) are measured during a separate experiment without the reactor. Fig. 3
(g) shows that the effluent stream contains a combination of different isomers of C8H10, with m-xylene appearing to be the most abundant one. Xylene offers a convenient benchmark problem for quantitative isomer discrimination, described in detail in Section 3.4
, which is a novel aspect in PEPICO analysis introduced in our work.
In addition to the various isomers of xylene, isomers of trimethylbenzene can be generated through direct methylation or dehydrogenation-methylation of lighter hydrocarbons (Cesarini et al., 2022). Despite the detection of only a negligible number of cations with mass 120 in the TOF spectrum [Fig. 2
(b)], the comparison of the extracted CIY-PES with reference spectra [Fig. 3
(h)] indicates the presence of a mixture of different isomers of trimethylbenzenes in our experiment (Longetti et al., 2020
). It is worthwhile mentioning that CIY-PES for mass 120 only shows the electrons coming from the ionization channel that leads to the removal of one electron. On the other hand, reference PES includes electrons coming from all ionization channels.
3.4. Isomer quantification
Quantitative discrimination of isomers from PEPICO data provides a valuable tool for analyzing complex reaction pathways in catalytic reactions of hydrocarbons. The reference spectra for different isomers of xylene, measured in the absence of reactor, are depicted in Fig. 3(g) along with the CIY-PES for mass 106 and its combination with masses 105, and 91 from the reactor effluent stream. The major differences between these spectra lies in their first and third bands in the 8–10 and 13–14 eV regions of the binding energy, respectively. The ionization channel of
is correlated to the electrons with binding energy of 8–10 eV. Moreover, for the reference spectra, electrons coming from the background (H2O, N2 and O2) do not overlap with xylene electrons coming from the ionization channel of
. Therefore, we are going to focus on the first band to quantitatively distinguish the ratio of different isomers of xylene in the effluent.
A comparison between CIY-PES for mass 106 with reference spectra of xylene isomers is given in Fig. 4(a). The CIY-PES for mass 106 does not have the two separate peaks which are characteristic of p-xylene. In addition, its FWHM is almost equal to m-xylene. Therefore, m-xylene is the dominant isomer among the products. But what is the exact branching ratio?
![]() | Figure 4 Comparison between (a) CIY-PES for mass 106 with reference PES of m-xylene and p-xylene, (b) and (c) reference PES of m-xylene and p-xylene respectively, with their corresponding fits, and (d) CIY-PES for mass 106 with the deconvoluted peaks. |
In order to quantitatively determine the ratio of isomers, each reference spectrum has been deconvoluted using a collection of asymmetrically distorted Voigt profiles. For reference PES of m- and p-xylene, aggregation of three Voigt profiles is required to adequately describe the collected data [Figs. 4(b) and 4(c), respectively],
Here, ω shows the individual weight of each Voigt function. Then, these two groups of peaks were mixed in a specific ratio, while the peak shapes, center distances and intensity ratios within each group were fixed according to their values estimated from pure reference compounds. By iteratively adjusting the ratio of these two groups of peaks and minimizing the difference between the generated spectra and the one with unknown mixing ratio, one could quantify the mixing ratio. First, the method was benchmarked against two control mixtures of m- and p-xylenes with known compositions, 50:50 and 75:25, returning estimates of 56:44 and 77:23, respectively. This outcome demonstrates that, although promising, the isomer quantification analysis requires PEPICO data with higher signal-to-noise ratio than in the present data, and more systematic collection of calibration datasets. Next, we applied the same routine to analyze the reactor effluent. Fig. 4(d) demonstrates the quality of the resulting model fit. Based on this method, and considering the area of peaks, almost 85% of the electrons detected in coincidence with
cation are coming from m-xylene and the remaining 15% are related to p-xylene. This result agrees well with the selectivities reported in the literature for unmodified ZSM-5 (Zhang et al., 2015
; Gao et al., 2020
). Although p-xylene is more likely to be the prevalent primary product of toluene methylation inside the micropores, unmodified ZSM-5 in these studies is thought to contain external acid sites that rapidly isomerize p-xylene. Unneberg & Kolboe (1988
) have shown that the xylene isomer distribution over ZSM-5 catalysts can shift from meta to para with increasing time on stream. In our future work, we will apply isomer-selective PEPICO to systematically characterize p-/m-xylene selectivity in zeolites at low-pressure conditions, i.e. in the limit of low DME exposure, to fully understand what controls their intrinsic xylene selectivity.
4. Conclusion
Operando PEPICO mass-spectrometry is emerging as a valuable analytical tool for investigations of reaction mechanisms and kinetics in Currently, the scope of the technique and its adoption in the catalysis research community are constrained by the limited availability of dedicated facilities around the globe. We have established the analysis of catalytic reactor effluents using PEPICO and, potentially, other photoionization-based methods at the FinEstBeAMS beamline at MAX IV Laboratory. This capability was demonstrated using dimethyl ether conversion on a prototypical ZSM-5 catalyst (at 375°C and 5 × 10−7 mbar total pressure) as a benchmark reaction, which agreed with the product distribution expected from the literature. Due to the specific configuration of the reactor packing in our proof-of-principle study, we have not observed either ketene or methyl radical, both highly reactive intermediates that were recently revealed by operando PEPICO. However, we have quantitatively determined the ratio of xylene isomers in the product stream by deconvoluting their coincidence photoelectron spectra, opening up a new avenue for quantitative isomer-selective PEPICO analysis in kinetic studies of heterogeneously catalyzed reactions.
To enhance the technique, a differential pumping system is developing to facilitate high-pressure studies as well. In the current study, the reactor pressure was in the range 10−7 to 10−6 mbar. However, with the implementation of the differential pumping system, it will be feasible to conduct PEPICO experiments while the reactor is at atmospheric pressure. Overcoming the constraint of being limited to steady-state conditions, due to prolonged data acquisition times, requires using a different type of electron analyzer, such as electron TOF, which has higher transmission than the hemispherical one.
Supporting information
Supporting Figures S1 to S7. DOI: https://doi.org/10.1107/S1600577524004405/vy5024sup1.pdf
Acknowledgements
We acknowledge MAX IV Laboratory for time on FinEstBeAMS beamline under Proposals 20190444 and 20180449. Research conducted at MAX IV, a Swedish national user facility, is supported by the Swedish Research council under contract 2018-07152, the Swedish Governmental Agency for Innovation Systems under contract 2018-04969, and Formas under contract 2019-02496. We express our gratitude to Dr Antti Kivimäki and Dr Kirill Chernenko at the FinEstBeAMS beamline, MAX IV Laboratory, for their assistance during the experiments.
Funding information
This research was funded by the Research Council of Norway (No. 272266, TAPXPS project), the Research Council of Finland (No. 341288, IntriCAT project), and the University of Oulu Graduate School.
References
Arion, T. & Hergenhahn, U. (2015). J. Electron Spectrosc. Relat. Phenom. 200, 222–231. Web of Science CrossRef CAS Google Scholar
Batchu, R., Galvita, V. V., Alexopoulos, K., Van der Borght, K., Poelman, H., Reyniers, M.-F. & Marin, G. B. (2017). Appl. Catal. Gen. 538, 207–220. CrossRef CAS Google Scholar
Bodi, A., Hemberger, P., Osborn, D. L. & Sztáray, B. (2013). J. Phys. Chem. Lett. 4, 2948–2952. CrossRef CAS Google Scholar
Brogaard, R. Y., Henry, R., Schuurman, Y., Medford, A. J., Moses, P. G., Beato, P., Svelle, S., Nørskov, J. K. & Olsbye, U. (2014). J. Catal. 314, 159–169. CrossRef CAS Google Scholar
Cejka, J., Corma, A. & Zones, S. (2010). Zeolites and Catalysis: Synthesis, Reactions and Applications. Wiley-VCH Verlag GmbH & Co. Google Scholar
Cesarini, A., Mitchell, S., Zichittella, G., Agrachev, M., Schmid, S. P., Jeschke, G., Pan, Z., Bodi, A., Hemberger, P. & Pérez-Ramírez, J. (2022). Nat. Catal. 5, 605–614. CrossRef CAS PubMed Google Scholar
Chang, C. D. (1983). Catal. Rev. 25, 1–118. CrossRef CAS Google Scholar
Chang, Y.-C., Xiong, B., Bross, D. H., Ruscic, B. & Ng, C. (2017). Phys. Chem. Chem. Phys. 19, 9592–9605. CrossRef CAS PubMed Google Scholar
Chernenko, K., Kivimäki, A., Pärna, R., Wang, W., Sankari, R., Leandersson, M., Tarawneh, H., Pankratov, V., Kook, M., Kukk, E., Reisberg, L., Urpelainen, S., Käämbre, T., Siewert, F., Gwalt, G., Sokolov, A., Lemke, S., Alimov, S., Knedel, J., Kutz, O., Seliger, T., Valden, M., Hirsimäki, M., Kirm, M. & Huttula, M. (2021). J. Synchrotron Rad. 28, 1620–1630. Web of Science CrossRef CAS IUCr Journals Google Scholar
Feng, R., Cooper, G. & Brion, C. (2001). Chem. Phys. 270, 319–332. CrossRef CAS Google Scholar
Gao, W., Guo, L., Cui, Y., Yang, G., He, Y., Zeng, C., Taguchi, A., Abe, T., Ma, Q., Yoneyama, Y. & Tsubaki, N. (2020). ChemSusChem, 13, 6541–6545. CrossRef CAS PubMed Google Scholar
Hemberger, P., van Bokhoven, J. A., Pérez-Ramírez, J. & Bodi, A. (2020). Catal. Sci. Technol. 10, 1975–1990. CrossRef CAS Google Scholar
Huber, P. & Plessow, P. N. (2023). J. Catal. 428, 115134. CrossRef Google Scholar
Kimura, K. (1981). Handbook of HeI Photoelectron Spectra of Fundamental Organic Molecules. Halsted Press. Google Scholar
Koenig, T., Tuttle, M. & Wielesek, R. (1974). Tetrahedron Lett. 15, 2537–2540. CrossRef Google Scholar
Kooser, K., Kivimäki, A., Turunen, P., Pärna, R., Reisberg, L., Kirm, M., Valden, M., Huttula, M. & Kukk, E. (2020). J. Synchrotron Rad. 27, 1080–1091. Web of Science CrossRef CAS IUCr Journals Google Scholar
Kukk, E., Sankari, R., Huttula, M., Sankari, A., Aksela, H. & Aksela, S. (2007). J. Electron Spectrosc. Relat. Phenom. 155, 141–147. Web of Science CrossRef CAS Google Scholar
Li, Y. & Yu, J. (2021). Nat. Rev. Mater. 6, 1156–1174. CrossRef CAS Google Scholar
Longetti, L., Randulová, M., Ojeda, J., Mewes, L., Miseikis, L., Grilj, J., Sanchez-Gonzalez, A., Witting, T., Siegel, T., Diveki, Z., van Mourik, F., Chapman, R., Cacho, C., Yap, S., Tisch, J. W. G., Springate, E., Marangos, J. P., Slavíček, P., Arrell, C. A. & Chergui, M. (2020). Phys. Chem. Chem. Phys. 22, 3965–3974. CrossRef CAS PubMed Google Scholar
Olsbye, U., Svelle, S., Bjørgen, M., Beato, P., Janssens, T. V., Joensen, F., Bordiga, S. & Lillerud, K. P. (2012). Angew. Chem. Int. Ed. 51, 5810–5831. CrossRef CAS Google Scholar
Omojola, T., Logsdail, A. J., van Veen, A. C. & Nastase, S. A. F. (2021). Phys. Chem. Chem. Phys. 23, 21437–21469. CrossRef CAS PubMed Google Scholar
Pärna, R., Sankari, R., Kukk, E., Nõmmiste, E., Valden, M., Lastusaari, M., Kooser, K., Kokko, K., Hirsimäki, M., Urpelainen, S., Turunen, P., Kivimäki, A., Pankratov, V., Reisberg, L., Hennies, F., Tarawneh, H., Nyholm, R. & Huttula, M. (2017). Nucl. Instrum. Methods Phys. Res. A, 859, 83–89. Google Scholar
Prümper, G. & Ueda, K. (2007). Nucl. Instrum. Methods Phys. Res. A, 574, 350–362. Google Scholar
Redekop, E. A., Lazzarini, A., Bordiga, S. & Olsbye, U. (2020). J. Catal. 385, 300–312. CrossRef CAS Google Scholar
Rohatgi, A. (2022). Webplotdigitizer, Version 4.6, https://automeris.io/WebPlotDigitizer. Google Scholar
Rojo-Gama, D., Mentel, L., Kalantzopoulos, G. N., Pappas, D. K., Dovgaliuk, I., Olsbye, U., Lillerud, K. P., Beato, P., Lundegaard, L. F., Wragg, D. S. & Svelle, S. (2018). J. Phys. Chem. Lett. 9, 1324–1328. CAS PubMed Google Scholar
Salaneck, W. R. (1981). Intermolecular Relaxation Effects in the Ultraviolet Photoelectron Spectroscopy of Molecular Solids, ch. 11, pp. 121–149. Am. Chem. Soc. Publications (https://pubs.acs.org/doi/abs/10.1021/bk-1981-0162.ch011). Google Scholar
SLS (2023). The VUV beamline, https://www.psi.ch/en/sls/vuv. Google Scholar
Stockbauer, R. & Inghram, M. G. (1975). J. Chem. Phys. 62, 4862–4870. CrossRef CAS Google Scholar
Sztáray, B., Voronova, K., Torma, K. G., Covert, K. J., Bodi, A., Hemberger, P., Gerber, T. & Osborn, D. L. (2017). J. Chem. Phys. 147, 013944. PubMed Google Scholar
Tang, X., Garcia, G. A., Gil, J. & Nahon, L. (2015). Rev. Sci. Instrum. 86, 123108. CrossRef PubMed Google Scholar
Unneberg, E. & Kolboe, S. (1988). Studies Surf. Sci. Catal. 36, 195–199. CrossRef CAS Google Scholar
Wallace, W. E. (2018). NIST Chemistry Webbook – NIST standard reference database No. 69, https://webbook.nist.gov/chemistry/. Google Scholar
Wen, W., Yu, S., Zhou, C., Ma, H., Zhou, Z., Cao, C., Yang, J., Xu, M., Qi, F., Zhang, G. & Pan, Y. (2020). Angew. Chem. Int. Ed. 59, 4873–4878. CrossRef CAS Google Scholar
Xie, J. & Olsbye, U. (2023). Chem. Rev. 123, 11775–11816. CrossRef CAS PubMed Google Scholar
Ying, J., Zhu, H., Mathers, C., Gover, B., Banjavčić, M., Zheng, Y., Brion, C. & Leung, K. (1993). J. Chem. Phys. 98, 4512–4519. CrossRef CAS Google Scholar
Zhang, J., Qian, W., Kong, C. & Wei, F. (2015). ACS Catal. 5, 2982–2988. CrossRef CAS Google Scholar
Zhou, Z., Du, X., Yang, J., Wang, Y., Li, C., Wei, S., Du, L., Li, Y., Qi, F. & Wang, Q. (2016). J. Synchrotron Rad. 23, 1035–1045. CrossRef CAS IUCr Journals Google Scholar
This is an open-access article distributed under the terms of the Creative Commons Attribution (CC-BY) Licence, which permits unrestricted use, distribution, and reproduction in any medium, provided the original authors and source are cited.